纺织学报 ›› 2019, Vol. 40 ›› Issue (09): 167-172.doi: 10.13475/j.fzxb.20181005606

• 服装工程 • 上一篇    下一篇

基于不同人体测量方法的数据一致性和可替换性研究

余佳佳, 李健()   

  1. 北京服装学院 服装艺术与工程学院, 北京 100029
  • 收稿日期:2018-10-30 修回日期:2019-06-11 出版日期:2019-09-15 发布日期:2019-09-23
  • 通讯作者: 李健
  • 作者简介:余佳佳(1994—),女,硕士生。主要研究方向为服装人体工学,服装结构。
  • 基金资助:
    北京市教委项目(KM201910012012);服装工效及功能创新设计北京市重点实验室项目(KYTG02170202)

Data consistency and replaceability based on different human measurement methods

YU Jiajia, LI Jian()   

  1. School of Fashion, Beijing Institute of Fashion Technology, Beijing 100029, China
  • Received:2018-10-30 Revised:2019-06-11 Online:2019-09-15 Published:2019-09-23
  • Contact: LI Jian

RichHTML

3

PDF (PC)

92

摘要：

为探究人体测量中三维数据与手工数据间的一致性和可替换性,及不同扫描仪所得结果间的数据等价性,利用HumanSolutions和[TC]2 2种三维扫描仪分别对20~35周岁的女性样本人体进行扫描,通过逆向工程软件手动测量388个样本的30项身体特征尺寸。对比2组三维数据与其对应手工数据的折线图,利用组内相关系数对数据的一致性进行探究;依据国标对三维数据与手工数据间的可替换性进行讨论和判别;以手工数据为媒介,对比2种三维数据与真实值间的一致性和可替换性,判断不同扫描仪数据结果的等价性。结果表明:2种仪器所得数据与手工数据间存在较好的一致性,组内相关系数大于0.75,3种数据在部分测量项上具有较好的可替换性,进行数据处理和分析时可等价使用。

关键词: 人体测量方法, 三维扫描, 一致性, 可替换性, 组内相关系数

Abstract:

In order to explore consistency and substitutability between human data results obtained by three-dimensional (3-D) scanners and manual data as well as the data equivalence between the results obtained by different scanners, this paper used HumanSolutions and [TC]2 3-D scanners to scan the samples of women between the ages of 20-35, and 30 somatotype indexes of 388 samples were manually measured by Rapidform XOR3. The consistency of the 3-D data and their corresponding manual data were checked using line chart and intraclass correlation coefficient (abbreviate it to ICC). The replaceability of the data were checked according to the national standard. With manual data as a medium, the data consistency and replaceability between two kinds of 3-D data and the real size value were compared to judge the equivalence of different 3-D data. The results show that good consistency exists between 3-D data and manual data(ICC>0.75), and the three data of Human Solutions 3-D scan, [TC]2 3-D scanning and manual measurement are replaceable on partial measurement terms, and can be used equivalently in data processing and analysis.

Key words: manual measurement method, three-dimensional scan, consistency, replaceability, intraclass correlation coefficient

中图分类号: 

  • TS941.17

表1

三维人体扫描仪参数比较"

仪器
名称		 国家 光源 扫描时间/
s		 数据密度/
(字节·s-1)		 准确度/
mm
Human
Solutions		 德国 激光 8~20 2 000 000 5~60
[TC]2 美国 白光 8 400 000 1~2

图1

不同扫描仪数据与手工数据对比"

表2

三维数据与手工数据组内相关系数表"

测量项目 CH CT 测量项目 CH CT
颈根围 0.977 0.855 肩幅 0.950 0.921
胸围 0.982 0.983 颈根厚 0.973 0.766
乳下围 0.994 0.974 乳点位厚 0.992 0.968
腰围 0.998 0.982 胸围位中心厚 0.997 0.946
腹部前突点围 0.998 0.960 乳下围位厚 0.985 0.960
臀围 0.996 0.951 腰围位厚 0.995 0.960
小腿最突点围 0.999 0.967 腹部前突点厚 0.984 0.940
颈根宽 0.782 0.622 臀围位厚 0.989 0.940
乳点间距 0.967 0.899 小腿最突围厚 0.896 0.913
乳点位宽 0.974 0.938 后中心长 0.949 0.846
乳下围位宽 0.972 0.946 后长 0.883 0.692
腰围位宽 0.991 0.932 前中心长 0.912 0.790
腹部前突点宽 0.992 0.913 前长 0.932 0.693
臀围位宽 0.969 0.879 肩宽1 0.599 0.292
小腿最突围宽 0.940 0.916 肩宽2 0.541 0.322

表3

三维数据与手工数据可替换性检验表"

测量项目 ΔH ΔT 最大允
差/cm
颈根围 [-0.2,0.4] [-0.3,0.3] 0.4
胸围 [-1.0,-0.6] [-0.2, 1.0 ] 0.9
乳下围 [-0.4,-0.2] [-0.2,0.5] 0.9
围度 腰围 [-0.2,0.5] [-0.2,1.7] 0.9
腹部前突点围 [-0.1,0.4] [-0.2,0.9] 0.9
臀围 [-0.4,-0.2] [-0.2,1.2] 0.9
小腿最突点围 [-0.4,-0.2] [-0.1,0.4] 0.4
颈根宽 [-0.5,0.2] [-0.5,-0.1] 0.4
乳点间距 [-0.2,0.3] [-0.2,0.2] 0.4
乳点位宽 [-0.6,-0.4] [-0.2,0.5] 0.4
乳下围位宽 [-0.5,-0.4] [-0.1,0.6] 0.4
宽度 腰围位宽 [0.2, 0.7] [-0.1,1.3] 0.4
腹部前突点位宽 [-0.2,0.1] [-0.1,0.8] 0.4
臀围位宽 [-0.6,-0.4] [-0.1,1.5] 0.4
小腿最突围宽 [0.1,0.7] [-0.1,1.1] 0.4
肩幅(SP1) [0.3,0.7] [-0.1, 0.5] 0.4
颈根厚 [0.2,0.4] [-0.1,0.3] 0.5
乳头点位厚 [0.1,0.7] [-0.1,1.3] 0.5
胸围位中心厚 [0.1,0.3] [-0.2,1.6] 0.5
厚度 乳下围位厚 [0.0,0.6] [-0.1,1.1] 0.5
腰围位厚 [0.0,0.3] [-0.1,1.2] 0.5
腹部前突点厚 [0.1,0.6] [-0.1,0.7] 0.5
臀围位厚 [-0.1,0.3] [-0.1,1.5] 0.5
小腿最突围厚 [-0.1,0.5] [-0.1,1.3] 0.5
后中心长 [0.7,1.0] [0.5,0.7] 0.5
后长 [0.3,0.5] [-0.3,0.5] 0.5
实长 前中心长 [-0.8,-0.5] [-0.7,-0.2] 0.5
前长 [-0.5,-0.3] [-0.4, 0.4] 0.5
肩宽2 [-0.1,0.2] [-0.5,-0.2] 0.5
肩宽1 [-0.5,-0.1] [-0.2,0.5] 0.5

图2

HumanSolutions与[TC]2扫描点云截面对比"

图3

[TC]2-腰围点云截面图"

[1] 席焕久, 陈昭. 人体测量方法[M].2版. 北京: 科学出版社, 2010: 318.
XI Huanjiu, CHEN Zhao. Anthropometric Methods[M].2nd ed. Beijing: Science Press, 2010: 318.
[2] 刘咏梅, 张小雪, 郭云昕. 国内外服装用人体数据库调查与分析[J]. 纺织学报, 2015,36(6):141-147.
LIU Yongmei, ZHANG Xiaoxue, GUO Yunxin. Survey and analysis on domestic and overse as human body database for garments'use[J]. Journal of Textile Reasearch, 2015,36(6):141-147.
[3] 李镒冲, 李晓松. 两种测量方法定量测量结果的一致性评价[J]. 现代预防医学, 2007,34(17):3263-3266.
LI Yichong, LI Xiaosong. Evaluation on different assessment methods of consistency of quantitatice measurements[J]. Modern Preventive Medicine, 2007,34(17):3263-3266.
[4] 张淑君, 丁笑君, 邹奉元. 三维人体扫描仪测量数据与手工测量数据关系研究[J]. 浙江理工大学学报(自然科学版), 2006,23(3):298-301.
ZHANG Shujun, DING Xiaojun, ZOU Fengyuan. Research on the relationship between data extracted from 3D body scanner and manual data[J]. Journal of Zhejiang Sci-Tech University(Natural Sciences Edition), 2006,23(3):298-301.
[5] 邹奉元, 张颖. 基于不同方法的人体测量数据重复性研究[J]. 纺织学报, 2004,25(4):71-71.
ZOU Fengyuan, ZHANG Ying. Research on repeatability of anthropometric data based ondifferent methods[J]. Journal of Textile Reasearch, 2004,25(4):71-73.
[6] LI J, ZHENG R, ZHANG H, et al. A Comparative Study on anthropometric data from different body measuring methods. [C]//LI Y,LIU YF, L XN, et al. Textile Bioengineering and Informatics Symposium Proceeding. Hong Kong: Binary Information Press, 2011: 104-111.
[7] 徐继红, 张文斌. 非接触式三维人体扫描技术的综述[J]. 扬州职业大学学报, 2006,10(3):49-53.
XU Jihong, ZHANG Wenbin. Review of noncontact 3D body scanning technology[J]. Journal of Yangzhou Polytechnic College, 2006,10(3):49-53.
[8] BARTKO J J. The intraclass correlation coefficient as a measure of reliability[J]. Psycholog Rep, 1966,19(1):3.
[9] 余红梅, 罗艳虹, 萨建, 等. 组内相关系数及其软件实现[J]. 中国卫生统计, 2011,28(5):497-500.
YU Hongmei, LUO Yanhong, SA Jian, et al. Intraclass correlation coefficient and software procedures[J]. Chinese Journal of Health Statistics, 2011,28(5):497-500.
[10] 潘晓平, 倪宗瓒. 组内相关系数在信度评价中的应用[J]. 四川大学学报(医学版), 1999,30(1):62-63.
PAN Xiaoping, NI Zongzan. Application of intraclass correlation coefficient to reliability assessment[J]. Journal of Sichuan University(Medical Science Edition), 1999,30(1):62-63.
[11] 李雪君. 呼吸对人体尺寸的影响[J]. 纺织科技进展, 2015(6):59-61.
LI Xuejun. Influence of breathing on body dimen-sion[J]. Progress in Textile Science & Technology, 2015(6):59-61.
[1] 刘芸, 修毅. 基于B / S 架构的数字人台变形NURBS 曲面模型[J]. 纺织学报, 2020, 41(10): 137-143.
[2] 史玉媛 申鸿 魏振乾. 腰省量分配对无袖修身旗袍造型的影响[J]. 纺织学报, 2018, 39(08): 105-109.
[3] 罗治平;丁浩;张永宇. 移圈针沟槽的加工工艺[J]. 纺织学报, 2010, 31(10): 129-133.
[4] 杨刚;;钟跃崎;. 基于同层穿透补偿的扫描服装模型的重用性[J]. 纺织学报, 2010, 31(10): 134-138.
[5] 徐继红;张文斌. 人体与服装特征曲面间距离松量的影响因子[J]. 纺织学报, 2009, 30(05): 104-108.
[6] 徐继红;张文斌;肖平. 人体与服装特征曲面间面积松量的分配关系[J]. 纺织学报, 2008, 29(5): 102-106.
[7] 郑芝奖;刘从九. 强力仪测定棉纤维断裂比强度的一致性研究[J]. 纺织学报, 2000, 21(03): 23-24.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
京ICP备14006648号　 京公网安备11010502044800号
版权所有 © 2021 《纺织学报》编辑部
地址： 北京市朝阳区延静里中街3号主楼6层《纺织学报》杂志社　邮政编码：100025　
电话：010-65017711,65917740　传真：010-65016539　Email:fangzhixuebao@vip.126.com
本系统由北京玛格泰克科技发展有限公司设计开发