纺织学报 ›› 2015, Vol. 36 ›› Issue (12): 125-130.

• 机械与器材 • 上一篇    下一篇

基于ADAMS的钢丝圈性能分析

  

  • 收稿日期:2014-11-14 修回日期:2015-08-28 出版日期:2015-12-15 发布日期:2015-12-10

Analysis of traveller performance based on ADAMS

  • Received:2014-11-14 Revised:2015-08-28 Online:2015-12-15 Published:2015-12-10

摘要:

随着细纱高速化的发展,钢丝圈是否合理、钢丝圈与钢领配合是否恰当都对成纱质量有较大影响,为此,对钢领与钢丝圈间的受力进行分析,然后运用SolidWorks软件建立PG1-4254型钢领以及6903-7/0型、FO-7/0型、U1ULUDR-5/0型钢丝圈的实体模型,最后运用Adams对钢领钢丝圈进行仿真分析,指出:U1ULUDR型钢丝圈对钢领瞬时冲击力最小,运行平稳性最好;FO型钢丝圈运行平稳性较U1ULUDR型次之,力的峰值较大;6903型钢丝圈对钢领的瞬时冲击力最大,运行平稳性较差。本文为分析钢领钢丝圈间受力提供了分析方法,同时为钢领钢丝圈的合理使用、设计与制造提供理论参考。

关键词: 钢丝圈, 受力分析, SolidWorks 软件, ADAMS软件

Abstract:

With the increasing of the spinning speed, whether the geometric shape of traveller is reasonable and whether the matching of the traveler and the ring is proper tave great influence on the yarn quality. The force between ring and traveller was analyzed firstly. Then, entity models of ring and three kinds of travellers were built in SolidWorks. Finally, simulation analysis of ring and traveler were conducted in Adams. In summary, the conclusion is that U1ULUDR traveller using performance is the best one and FO traveller using performance is better than 6903 traveller. This paper provides a method for the analysis of the force between ring and traveller and a theoretic basis for traveller using, design and manufacture.

Key words: traveler, force analysis, SolidWorks, ADAMS

中图分类号: 

  • TS 103.8
[1] 温欣婷 徐伯俊 刘新金. BC9型钢丝圈气圈底端张力特性分析[J]. 纺织学报, 2016, 37(08): 119-124.
[2] 李思颖 徐伯俊 刘新金. 钢丝圈空间倾角分析[J]. 纺织学报, 2015, 36(08): 127-132.
[3] 宋晓亮 刘建立 徐阳 刘基宏 高卫东. 光电式环锭断纱在线检测系统[J]. 纺织学报, 2014, 35(8): 94-0.
[4] 庚在海;吴文英;陈瑞琪. 钢丝圈空间位置分析[J]. 纺织学报, 2006, 27(7): 37-39.
[5] 李玮茹;张士俊;俞建勇. 粘接式气囊接口受力及接口临界长度的研究[J]. 纺织学报, 2005, 26(1): 92-94.
[6] 朱泽飞;林建忠. 纤维状粒子在气流场中的受力状况研究[J]. 纺织学报, 2000, 21(05): 8-10.
[7] 靳向煜;朱远胜;王俊. 围海造地中的充泥管袋应用研究[J]. 纺织学报, 2000, 21(05): 56-59.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] 姚杰;叶国铭. 纱条不匀的混沌特性[J]. 纺织学报, 2005, 26(1): 47 -48 .
[2] 王连贵. 多功能花式捻线机罗拉支承结构讨论[J]. 纺织学报, 1984, 5(09): 33 -35 .
[3] . 1985年针织工业学术座谈会[J]. 纺织学报, 1986, 7(05): 44 .
[4] 于伟东;刘洪玲;章悦庭 . 羊毛细化与定形的基本理论[J]. 纺织学报, 2005, 26(2): 15 -17 .
[5] 殷瑛;郑今欢;张玲玲;陈维国. 热处理对PTT纤维结构和力学性能的影响[J]. 纺织学报, 2006, 27(11): 32 -35 .
[6] 褚皎鸿. 怎样修理织机边撑[J]. 纺织学报, 1982, 3(10): 12 .
[7] 朱瑞意. 织厂设计和改造时的噪声控制[J]. 纺织学报, 1989, 10(08): 34 -36 .
[8] 钟照田. 稀土染色实践中几个问题的讨论[J]. 纺织学报, 1991, 12(04): 43 .
[9] 夏正兴. 山东纺织工学院简介[J]. 纺织学报, 1982, 3(09): 4 .
[10] 韩宝康;谢月香;陈邦伟. 提高提花毛浴巾柔软度工艺探讨[J]. 纺织学报, 1987, 8(02): 52 -55 .