纺织学报 ›› 2016, Vol. 37 ›› Issue (01): 152-158.

• 机械与器材 • 上一篇    下一篇

宽幅热定型机拉幅系统的模糊PID控制与实验

  

  • 收稿日期:2015-01-12 修回日期:2015-09-21 出版日期:2016-01-15 发布日期:2016-01-14

Fuzzy-PID control and experimental for stentering system of wide heat-setting machine

  • Received:2015-01-12 Revised:2015-09-21 Online:2016-01-15 Published:2016-01-14

摘要:

针对拉幅系统张力和摆臂位置的波动、超调和响应特性较差的问题,通过模糊PID控制算法实现拉幅张力和针板链条张力稳定以及摆臂网边的高跟随精度。结果表明,模糊PID控制算法可有效改善拉幅系统的动态特性。拉幅张力的超调量小于0.5KN,调整时间由11.9s降低到6.8s,拉幅张力稳定在87±1KN;针板链条张力受到干扰后能够在不产生超调的前提下仅需2s就能回到稳定状态;摆臂位置跟随系统也不会产生超调且能快速响应。运用Fuzzy-PID控制算法降低了张力与摆臂位置的波动和超调量,提高了热定型拉幅系统动态响应和稳态特性。

关键词: 宽幅热定型机, 拉幅控制系统, 模糊PID, 动态响应

Abstract:

To solve the problems of fluctuation and overshoot and poor response characteristics of tentering system tension and arm swing, the fuzzy-PID control algorithm to achieve the tension stability of stentering tension and needle plate chain and high tracking accuracy of Swing arm fabric edge. The results showed that The Fuzzy-PID control algorithm can effectively improve the dynamic characteristics of stentering system.The overshoot of stentering tension is less than 0.5KN, and the adjust-time decreased from 11.9s to 6.8s, and the stentering tension stabilized at 87±1KN.After a disturbance the needle plate chain tension can return to steady state in only 2 second and does not produce the premise of overshoot.The following system of swing arm position will not cause overshoot and it will response quickly.Using Fuzzy-PID control algorithm can reduce the fluctuations and overshoot of the tension and the swing arm position, and improve the dynamic response and steady state characteristics of stentering system.

Key words: wide heat-setting machine, stretching control system, fuzzy-PID, dynamic response

[1] 贾雪 罗勇 徐恒博. EMD-ESN模型在热牵伸辊温控系统中的应用[J]. 纺织学报, 2014, 35(7): 128-0.
[2] 刘苏 夏风林 张琦 蒋高明. 经编电子送经的模糊PID控制设计[J]. 纺织学报, 2013, 34(8): 127-0.
[3] 张琦, 蒋高明, 夏风林, 秦文, 殷明跃. 高速经编机电子横移控制模型选择及动态响应分析[J]. 纺织学报, 2012, 33(1): 126-131.
[4] 张政;魏俊民. 雾化喷嘴工作参数的模糊PID复合控制[J]. 纺织学报, 2007, 28(3): 100-103.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] 阎德顺;俞芸芸;张恕;朱关福. 凝结法回收退浆废水中聚乙烯醇[J]. 纺织学报, 1984, 5(08): 42 -46 .
[2] . 耐用节电钢领钢丝圈使用经验介绍[J]. 纺织学报, 1990, 11(03): 42 .
[3] 谌玉红.;李若新;姜志华;郝俊勤. 出汗假人系统特征方程与稳定性判定[J]. 纺织学报, 2006, 27(10): 67 -69 .
[4] 关芳兰. 纳米氧化锌功能纺织品的制备及其稳定性[J]. 纺织学报, 2009, 30(01): 64 -67 .
[5] 秦锡林;王士根;徐福根. B311B毛精梳机拔取差动机构及其改进[J]. 纺织学报, 1981, 2(06): 50 -53 .
[6] 陈海相;余志成;陈文兴;胡智文. β-环糊精修饰纤维素纤维的制备[J]. 纺织学报, 2003, 24(05): 20 -22 .
[7] 沈精虎;王晓红. 图像处理在特种动物毛纤维识别中的应用[J]. 纺织学报, 2004, 25(04): 26 -27 .
[8] 秦益民. 利用甲壳胺和海藻酸钠处理染整废水[J]. 纺织学报, 2005, 26(5): 137 -139 .
[9] 范晓旭;徐琪. 基于XML中间件的服装供应链快速响应系统[J]. 纺织学报, 2009, 30(04): 123 -128 .
[10] 郑秀实. 中国纺织工程学会染色新技术学术讨论会[J]. 纺织学报, 1987, 8(10): 64 .