纺织学报 ›› 2017, Vol. 38 ›› Issue (08): 139-143.doi: 10.13475/j.fzxb.20160605905

• 机械与器材 • 上一篇    下一篇

FA322B并条机牵伸机构主牵伸区部分参数的优化设计

  

  • 收稿日期:2016-06-22 修回日期:2017-05-11 出版日期:2017-08-15 发布日期:2017-08-10

Design and optimization of partial parameters of main drafting for FA322B drawing frame

  • Received:2016-06-22 Revised:2017-05-11 Online:2017-08-15 Published:2017-08-10

摘要:

用不同长度纤维在FA322B型并条机上并条牵伸,通常需要根据人工经验调整并条机牵伸机构的部分结构参数,较难达到最佳牵伸效果。为此,在分析FA322B型并条机牵伸机构工作原理的基础上,通过建模优化方式,得到主牵伸区中二皮辊和二罗拉横向距离的最佳调整位置,为实际生产中工艺调整提供理论指导。同时研究二皮辊和二罗拉横向距离大小对牵伸效果的影响。研究结果表明:二皮辊和二罗拉横向距离选取不当会致使纤维黏附于前皮辊之上,严重影响牵伸效果,因此在实际生产中,需要合理调整二皮辊和二罗拉横向距离,以保证良好的牵伸效果。

关键词: 并条机, 牵伸机构, 纤维品质长度, 牵伸效果

Abstract:

For drawing and drafting fibers of different lengths on the FA322B drawing frame, partial process parameters of the drafting mechanism of the drawing frame are needed to artificial experience,but it is hard to achieve optimal drafting effect. In ordr to solve this problem, based on analyzing the operating principle of the drafting mechanism of the FA322B drawing frame, the modeling optimization was adopted to obtain the optimal adjustment position of the transverse distance between the  second upper and lower rollers, providing theoretical guide for the process adjustment in actual production. The influences of the transverse distance between the second upper and lower rollers on the drafting effect was also investigated. The results indicate that improper transverse distance between the second upper and lower rollers can carse fibers to adhere to the front upper roller, thereby greatly affecting the drafting effect. Therefore, transverse distance between the second upper and lower rollers should beadjusted carefully to ensure good drafting effect in actual production.

Key words: drawing frame, drafting mechanism, quality length of fiber, drafting effect

[1]. 邹项怡,朱俊凤. 并条机牵伸工艺配置的探讨[J]. 黑龙江纺织,2010-3. [2]. 刘大勇,余仁君. 并条机牵伸工艺的配置及牵伸机构缺陷的探讨[J]. 现代纺织技术,2004, 12(5):33-36. [3]. 张新江. FA322B自调匀整并条机性能特点及使用效果分析[J]. 现代纺织技术,2012-3,30-35. [4]. 袁景山. 压力棒牵伸机构的优化设计[J]. 棉纺织技术,1990-1, (12):725-729.

[1] 高志娟 郁崇文. 并条机后区牵伸倍数的模拟设计[J]. 纺织学报, 2017, 38(04): 39-45.
[2] 宋栓军. 并条机牵伸罗拉同步性检测方法[J]. 纺织学报, 2016, 37(09): 123-128.
[3] 束永平;矫海静. 细纱机双皮圈牵伸装置的静态正压力分析[J]. 纺织学报, 2011, 32(4): 123-127.
[4] 英迪;汪军;田承泰. 牵伸力与并条条子质量的关系[J]. 纺织学报, 2010, 31(3): 111-115.
[5] 李宏亮;周武能;王新厚;. 并条机自调匀整双开环控制系统[J]. 纺织学报, 2010, 31(2): 106-109.
[6] 谢永奇;高红霞;余建祖;赵然. JWF-A型并条机吸风系统气流流场的数值仿真[J]. 纺织学报, 2009, 30(9): 109-114.
[7] 朱立成;顾闻彦;葛明桥. 旋流纺闭合式纤维集聚机构的设计[J]. 纺织学报, 2008, 29(6): 105-108.
[8] 陈剑飞;许晓桢;徐战彬. 并条机罗拉齿面冷轧成形技术[J]. 纺织学报, 2005, 26(5): 37-39.
[9] 姚杰;叶国铭. 新型开环自调匀整装置的分析与设计[J]. 纺织学报, 2005, 26(3): 44-45.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!