Journal of Textile Research ›› 2021, Vol. 42 ›› Issue (03): 56-63.doi: 10.13475/j.fzxb.20200602108

;

• Fiber Materials • Previous Articles     Next Articles

Application of rabbit hair based hollow carbon fiber in lithium-sulfur battery

CHEN Junyan1,2, JU Jingge1,2, DENG Nanping1,2, YANG Qi1,2, CHENG Bowen1,2, KANG Weimin1,2()   

  1. 1. School of Textile Science and Engineering, Tiangong University, Tianjin 300387, China
    2. State Key Laboratory of Separation Membrane and Membrane Process, Tiangong University, Tianjin 300387, China
  • Received:2020-06-08 Revised:2020-11-16 Online:2021-03-15 Published:2021-03-17
  • Contact: KANG Weimin E-mail:kweimin@126.com

RichHTML

6

PDF (PC)

97

Abstract:

In order to develop a high-performance and low-cost lithium-sulfur battery cathode sulfur storage material, the rabbit hair hollow carbon fiber (RC) with heteroatom doping was successfully prepared by using natural biomass fiber as the precursor. After pretreatment and carbonization, the sulfur/rabbit hair carbon fiber (S/RC) composite material is prepared by hot melting method. The effects of different carbonization temperatures on the morphology and structure of carbon fibers, the crystalline structure and conductivity of S/RC composites, the electrochemical performance of lithium-sulfur batteries and the stability of cyclic charge and discharge were discussed. The results show that when the pretreatment temperature is 300 ℃ and the carbonization temperature is 800 ℃, the morphology and structure of the prepared rabbit hair hollow carbon fiber are the most intact; the battery prepared with it has a first discharge specific capacity of 899 mA·h/g, and at 0.5C after 300 cycles, the discharge specific capacity became 598 mA·h/g, retaining 66.52% of the original specific capacity. Under high rate conditions, the battery still has a high discharge specific capacity, and the discharge specific capacities at 1C and 2C are 543.8 and 505.4 mA·h/g respectively.

Key words: rabbit hair, hollow carbon fiber, lithium-sulfur battery, anode material, biomass fiber

CLC Number: 

  • TS139

Fig.1

Schematic of formation of S/RC composite materials"

Fig.2

SEM images of rabbit hair at different stages of preparation. (a)Raw rabbit hair fiber;(b)Pre-oxidation rabbit hair;(c)RC-700;(d)RC-800;(e)RC-900;(f)S/RC-800"

Fig.3

TEM images of rabbit hollow hair based carbon fibers"

Tab.1

Percentage of surface element content of RC-800 and S/RC%"

样品名称 含量
C N O P S
RC-800 75.72 6.61 7.70 6.34 3.63
S/RC-700 56.36 4.01 4.17 1.37 34.09
S/RC-800 57.75 3.53 3.66 1.14 33.92
S/RC-900 58.35 3.49 2.17 0.82 35.17

Fig.4

XRD patterns of RC and S/RC at different carbonization temperatures"

Fig.5

TG graphs of S/RC composites"

Fig.6

RC-800 and S/RC-800 adsorption-desorption isothermal curves (a) and pore diameter distribution (b)"

Fig.7

Electrochemical impedance diagrams and cyclic voltammetry curves of anode materials. (a)Impedance diagrams of S/RC and S/RC-CNTs;(b)Cyclic voltammetric curves of S/RC-CNTs-800 composite cathode materials"

Fig.8

Cycling performances of S/RC-CNTs composites at 0.5C"

Fig.9

Curves of first discharge/charging platform for S/RC-CNTs"

Fig.10

Curves of discharge/charging platform of S/RC-CNTs-800 at different magnification"

Fig.11

Curves of discharge/charging platform of S/RC-CNTs-800 at different number of cycles"

Fig.12

Multiplier property of S/RC-CNTs-800"

[1] 刘北元, 谢朝香, 崔志兴, 等. 氮掺杂多孔碳纤维改性锂硫电池正极材料[J]. 上海航天(中英文), 2020,37(2):69-74.
LIU Beiyuan, XIE Zhaoxiang, CUI Zhixing, et al. Nitrogen doped porous carbon fiber modified lithium sulfur battery anode material[J]. Aerospace Shanghai (Chinese & English), 2020,37(2):69-74.
[2] LARCHER D, TARASCON J M. Towards greener and more sustainable batteries for electrical energy storage[J]. Nature Chemistry, 2015,7(1):19-29.
doi: 10.1038/nchem.2085 pmid: 25515886
[3] 吴凯, 张耀, 曾毓群, 等. 锂离子电池安全性能研究[J]. 化学进展, 2011,23(2/3):402-408.
WU Kai, ZHANG Yao, ZENG Yuqun, et al. Study on safety performance of lithium ion battery[J]. Progress in Chemical, 2011,23(2/3):402-408.
[4] ZHAO H J, DENG N P, KANG W M, et al. The significant effect of octa(aminophenyl)silsesquioxane on the electrospun ion-selective and ultra-strong poly-m-phenyleneisophthalamide separator for enhanced electrochemical performance of lithium-sulfur battery[J]. Chemical Engineering Journal, 2020,381:122715.
[5] JAYAPRAKASH N, SHEN J, MOGANTY S S, et al. Porous hollow carbon@sulfur composites for high-power lithium-sulfur batteries[J]. Angewandte Chemie-International Edition in English, 2011,123:6026-6030.
[6] WU F, CHEN J, CHEN R, et al. Sulfur/polythiophene with a core/shell structure: synjournal and electrochemical properties of the cathode for rechargeable lithium batteries[J]. The Journal of Physical Chemistry C, 2011,115(13):6057-6063.
[7] ZHANG Y, WANG L, ZHANG A, et al. Novel V2O5/S composite cathode material for the advanced secondary lithium batteries[J]. Solid State Ionics, 2010,181(17/18):835-838.
[8] LIU J, YUAN L, YUAN K, et al. SnO2 as a high-efficiency polysulfide trap in lithium-sulfur batteries[J]. Nanoscale, 2016,8(28):13638-13645.
doi: 10.1039/c6nr02345b pmid: 27364768
[9] YANG Y, ZHENG G, MISRA S, et al. High-capacity micrometer-sized Li2S particles as cathode materials for advanced rechargeable lithium-ion batteries[J]. Journal of the American Chemical Society, 2012,134(37):15387-15394.
doi: 10.1021/ja3052206 pmid: 22909273
[10] JOZWIUK A, SOMMER H, JANEK J, et al. Fair performance comparison of different carbon blacks in lithium-sulfur batteries with practical mass loadings-simple design competes with complex cathode architecture[J]. Journal of Power Sources, 2015,296:454-461.
doi: 10.1016/j.jpowsour.2015.07.070
[11] SONG J, XU T, GORDIN M L, et al. Nitrogen-doped mesoporous carbon promoted chemical adsorption of sulfur and fabrication of high-areal-capacity sulfur cathode with exceptional cycling stability for lithium-sulfur batteries[J]. Advanced Functional Materials, 2014,24(9):1243-1250.
doi: 10.1002/adfm.201302631
[12] CHEN F, YANG J, BAI T, et al. Biomass waste-derived honeycomb-like nitrogen and oxygen dual-doped porous carbon for high performance lithium-sulfur batteries[J]. Electrochimica Acta, 2016,192:99-109.
doi: 10.1016/j.electacta.2016.01.192
[13] ZHAO J, YANG Y, KATIYAR R S, et al. Phosphorene as a promising anchoring material for lithium-sulfur batteries: a computational study[J]. Journal of Materials Chemistry A, 2016,4(16):6124-6130.
doi: 10.1039/C6TA00871B
[14] ZHOU G, PAEK E, HWANG G S, et al. Long-life Li/polysulphide batteries with high sulphur loading enabled by lightweight three-dimensional nitrogen/sulphur-codoped graphene sponge[J]. Nature Communications, 2015(6):7760-8760.
[15] YANG J, CHEN F, LI C, et al. A free-standing sulfur-doped microporous carbon interlayer derived from luffa sponge for high performance lithium-sulfur batteries[J]. Journal of Materials Chemistry A, 2016,4(37):14324-14333.
doi: 10.1039/C6TA06250D
[16] QU J, LV S, PENG X, et al. Nitrogen-doped porous "green carbon" derived from shrimp shell: combined effects of pore sizes and nitrogen doping on the performance of lithium sulfur battery[J]. Journal of Alloys and Compounds, 2016,671:17-23.
[17] WU H L, DENG Y L, MOU J, et al. Activator-induced tuning of micromorphology and electrochemical properties in biomass carbonaceous materials derived from mushroom for lithium-sulfur batteries[J]. Electrochimica Acta, 2017,242:146-158.
[18] WU H, XIA L, REN J, et al. A high-efficiency N/P co-doped graphene/CNT@porous carbon hybrid matrix as a cathode host for high performance lithium-sulfur batteries[J]. Journal of Materials Chemistry A, 2017,5(38):20458-20472.
doi: 10.1039/C7TA06504C
[19] LI F, QIN F, ZHANG K, et al. Hierarchically porous carbon derived from banana peel for lithium sulfur battery with high areal and gravimetric sulfur loading[J]. Journal of Power Sources, 2017,362:160-167.
[20] LI Y Y, WANG L, GAO B, et al. Hierarchical porous carbon materials derived from self-template bamboo leaves for lithium-sulfur batteries[J]. Electrochimica Acta, 2017,229:352-360.
[21] REN J, ZHOU Y B, WU H L, et al. Sulfur-encapsulated in heteroatom-doped hierarchical porous carbon derived from goat hair for high performance lithium-sulfur batteries[J]. Journal of Energy Chemistry, 2018,30:121-131.
[22] SU D S, SCHLOGL R. Nanostructured carbon and carbon nanocomposites for electrochemical energy storage applications[J]. Chem Sus Chem, 2010,3(2):136-68.
[23] 鞠敬鸽. 立体蜂窝状多孔碳纳米纤维基锂离子电容器负极材料研究[D]. 天津:天津工业大学, 2019, 36-48.
JU Jingge. Research on anode materials of three-dimensional cellular porous carbon nanofiber wire-based lithium ion capacitor[D]. Tianjin:Tiangong University, 2019: 36-48.
[24] 葛乃维, 张昊, 张毅. 兔毛角蛋白抗菌水凝胶的制备及其抗菌性能研究[J]. 中国养兔, 2019,6:4-11.
GE Naiwei, ZHANG Hao, ZHANG Yi. Preparation of rabbit hair keratin antibacterial hydrogel and study on its antibacterial properties[J]. Chinese Journal of Rabbit Farming, 2019,6:4-11.
[25] 邓南平. 锂硫电池用蜂窝多孔碳纳米纤维正极材料与芳纶隔膜的制备及性能研究[D]. 天津:天津工业大学, 2018, 37-51.
DENG Nanping. Preparation and properties of cellular porous carbon nanofiber membrane for lithium sulfur batteries[D]. Tianjin:Tiangong University, 2018: 37-51.
[26] WU H, MOU J, ZHOU L, et al. Cloud cap-like, hierarchically porous carbon derived from mushroom as an excellent host cathode for high performance lithium-sulfur batteries[J]. Electrochimica Acta, 2016,212:1021-1030.
doi: 10.1016/j.electacta.2016.07.153
[27] XU G, YAN Q B, KUSHIMA A, et al. Conductive graphene oxide-polyacrylic acid (GOPAA) binder for lithium-sulfur battery[J]. Nano Energy, 2017,31:568-574.
[28] ZHANG S S. Liquid electrolyte lithium/sulfur battery: Fundamental chemistry, problems, and solutions[J]. Journal of Power Sources, 2013,231:153-162.
[1] WANG Zixi, HU Yi. Preparation and energy storage of porous carbon nanofibers based on ZnCo2O4 [J]. Journal of Textile Research, 2020, 41(11): 10-18.
[2] LIU Huijie, XIA Xin. Influence of deep cryogenic treatment temperature on lithium electrical properties of SnSb/C nanofiber anode material [J]. Journal of Textile Research, 2019, 40(04): 38-43.
[3] DING Hao DING;HU Guoliang. DCCA treatment of rabbit hair fiber and property test [J]. JOURNAL OF TEXTILE RESEARCH, 2010, 31(8): 16-20.
[4] HOU Dayin;LI Liangfei;WEI Qufu. Surface modification of rabbit hair by low temperature plasma [J]. JOURNAL OF TEXTILE RESEARCH, 2007, 28(10): 15-17.
[5] LIU En-hua;LI Shu-feng;CHENG Bo-wen;DU Qi-yun. Study on preparation and structure of PAN-based hollow carbon fiber membrane [J]. JOURNAL OF TEXTILE RESEARCH, 2006, 27(4): 19-21.
[6] XI Bo-jun;TANG Li-min;ZHANG Cai-qian. Enzymatic treatment of rabbit hair fiber [J]. JOURNAL OF TEXTILE RESEARCH, 2006, 27(3): 21-23.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
京ICP备14006648号
Copyright 2021 © Editorial office of Journal of Textile Research
Supported by Beijing Magtech Co.Ltd