纺织学报 ›› 2020, Vol. 41 ›› Issue (05): 159-166.doi: 10.13475/j.fzxb.20190706608

• 机械与器材 • 上一篇    下一篇

多臂机旋转变速机构凸轮廓线建模与重构

肖志涛1,2, 尹洪环3, 于鸿彬2,3, 蒋秀明2,3, 邵宏宇4   

  1. 1.天津工业大学 电子与信息工程学院, 天津 300387
    2.天津工业大学 天津市现代机电装备技术重点实验室,天津 300387
    3.天津工业大学 机械工程学院, 天津 300387
    4.天津大学 机械工程学院, 天津 300072
  • 收稿日期:2019-07-29 修回日期:2020-01-16 出版日期:2020-05-15 发布日期:2020-06-02
  • 作者简介:肖志涛(1971—),男,教授,博士。主要研究方向为纺织机械智能信号处理技术与系统。
  • 基金资助:
    国家重点研发计划项目(2017YFB1104202)

Modeling and reconstruction of cam profile for dobby modulator

XIAO Zhitao1,2, YIN Honghuan3, YU Hongbin2,3, JIANG Xiuming2,3, SHAO Hongyu4   

  1. 1. School of Electronics and Information Engineering, Tiangong University, Tianjin 300387, China
    2. Key Laboratory of Advanced Mechatronics Equipment Technology, Tiangong University, Tianjin 300387, China
    3. School of Mechanical Engineering, Tiangong University, Tianjin 300387, China
    4. College of Mechanical Engineering,Tianjin University, Tianjin 300072, China
  • Received:2019-07-29 Revised:2020-01-16 Online:2020-05-15 Published:2020-06-02

RichHTML

5

PDF (PC)

52

摘要：

为提高旋转式多臂机的运动可靠性,对其旋转变速机构凸轮廓线进行建模求解,并运用粒子群算法进行凸轮廓线重构。首先,研究了旋转变速机构凸轮廓线数学模型构建方法,确定综框运动特性的多项式表达;其次,建立求解旋转变速机构凸轮廓线数学模型,获得基于综框运动特性的凸轮廓线,并建立多臂机提综机构数字样机,进行验证分析;最后,运用粒子群算法进行凸轮廓线重构方法研究,依据所构建的凸轮廓线逆向分析系统重构凸轮廓线。结果表明:提出的旋转变速机构凸轮廓线的数学求解方法,可基于粒子群算法进行凸轮廓线重构,显著提高凸轮廓线中心对称度。

关键词: 多臂机, 粒子群, 凸轮廓线, 建模与重构, 综框, 运动特性

Abstract:

In order to improve the motion reliability of rotary dobby, mathematical modeling of cam profile for dobby modulators was established, and the particle swarm optimization algorithm was used to reconstruct the cam profile. Firstly, the mathematical model construction method for the cam profile was studied to determine the polynomial expression for the heald frame motion characteristics. Secondly, the mathematical model for the cam profile was established, and the cam profile based on the motion characteristics of the heald frame was obtained. The digital prototype of the dobby was used for verification analysis. Finally, the particle swarm optimization algorithm was used to study the cam profile reconstruction method, and the cam profile was reconstructed according to the cam profile reverse analysis system. The research shows that the mathematical method for solving the cam profile of the dobby modulator has led to the cam profile reconstruction, and the central symmetry of the cam profile is improved. This meets the heald frame motion characteristics and provides a new and effective way to optimize the shedding mechanism for weaving machines.

Key words: dobby, particle swarm, cam profile, modeling and reconstruction, heald frame, motion characteristics

中图分类号: 

  • TH112

图1

旋转变速机构工作原理"

图2

偏心机构、运动传递机构和综框工作原理 13—偏心盘凸轮;14—环形连杆;15—提综臂;16—提综臂连杆;17—转臂;18—转臂连杆;19—综框连杆;20—支撑连杆;21—综框。"

图3

偏心机构、运动传递机构和综框简图"

图4

旋转变速机构简图"

表1

提综机构的物理参数和几何尺寸"

运动传递机构 偏心机构 旋转变速机构
参数 数值 参数 数值 参数 数值
lHI/mm 375 lO1O2/mm 192 lO1C/mm 111
lO3H/mm 200 lO2E/mm 96 lO1B/mm 43
lO2O3/mm 695 lDE/mm 170 lBA/mm 81
lO3G/mm 150 lO1D/mm 30 lAC/mm 56
lFG/mm 550 φ5/(°) 100 r/mm 31
lO2F/mm 185 — — — —
e/mm 200 — — — —
S0/mm 325 — — — —
φ9/(°) 98 — — — —

图5

逆向求解获得凸轮廓线"

图6

非中心对称凸轮产生的综框运动特性与11次曲线比较"

图7

粒子收敛的群体行为"

表2

修正系数与目标函数结果"

迭代次数 a b c 目标函数值
0 — — — 25 727.20
200 0.602 0.553 -0.155 14 583.06
400 0.843 0.550 -0.393 5 252.19
600 0.922 0.546 -0.468 2 007.61
800 0.950 0.544 -0.495 837.76
1 000 0.962 0.544 -0.506 324.61
1 200 0.968 0.544 -0.512 91.33
1 400 0.969 0.543 -0.512 39.06
1 600 0.969 0.544 -0.513 32.33
1 800 0.970 0.543 -0.513 31.51
2 000 0.970 0.543 -0.513 31.51
5 000 0.970 0.543 -0.513 31.51

图8

重构前后凸轮廓线比较"

图9

重构与测绘凸轮产生的综框运动特性比较"

[1] 祝章琛. 回转多臂机的设计与分析[J]. 纺织学报, 1985,6(2):97-100.
ZHU Zhangchen. Designing and analyzing of rotary dobby[J]. Journal of Textile Research, 1985,6(2):97-100.
[2] 金国光, 魏晓勇, 魏展, 等. 旋转式多臂机提综机构动力学分析与优化[J]. 纺织学报, 2018,39(9):160-168.
JIN Guoguang, WEI Xiaoyong, WEI Zhan, et al. Dynamic analysis and optimization of rotary dobby lifting comprehensive mechanism[J]. Journal of Textile Research, 2018,39(9):160-168.
[3] 张远华, 苟向锋, 陈晓芳, 等. 电子多臂机旋转变速机构共轭凸轮再设计[J]. 机械传动, 2018,42(4):57-61.
ZHANG Yuanhua, GOU Xiangfeng, CHEN Xiaofang, et al. Redesign of conjugate cam of rotation variable speed mechanism of electronic dobby[J]. Journal of Mechanical Transmission, 2018,42(4):57-61.
[4] 高大牛, 沈毅, 刘春雷. GT421型多臂机选综共轭凸轮设计[J]. 现代纺织技术, 2012,20(1):27-31.
GAO Daniu, SHEN Yi, LIU Chunlei. The design of election comprehensive conjugate cam of GT421 dobby[J]. Advanced Textile Technology, 2012,20(1):27-31.
[5] 高大牛, 沈毅, 刘春雷. 基于ADAMS的GT421型多臂机机构动态仿真[J]. 纺织学报, 2012,33(8):119-123.
GAO Daniu, SHEN Yi, LIU Chunlei. Dynamic simulation of mechanism of GT421 dobby based on ADAMS[J]. Journal of Textile Research, 2012,33(8):119-123.
[6] EREN R, OZKAN G, TURHAN Y. Kinematics of rotary dobby and analysis of heald frame motion in weaving procsee[J]. Textile Research Journal, 2008,78(12):1070-1079.
[7] EREN R, OZKAN G, KARAHAN M. Comparison of heald frame motion generated by rotary dobby and crank & cam shedding motions[J]. Fibres & Textiles in Eastern Europe, 2005,13(4):78-83.
[8] ANON. Rotary dobby: the efficient shed forming mechanism for modern weaving machines[J]. International Textile Bulletin: Fabric Forming, 1983,66:45-46.
[9] MARKS R, ROBINSON A T C. Principles of weaving[M]. London: The Textile Institute, 1976: 59-72.
[10] GUHA A, AMARNATH C, KURIEN I, et al. Linkage driven dobby with dwell[J]. Textile Research Journal, 2009,79(9):804-809.
[11] CHEW M, CHUANG C H. Minimizing residual vibrations in high-speed cam-follower systems over a range of speeds[J]. Journal of Mechanical Design, 1995,117(1):166-172.
[12] GUPTA K C, WIEDERRICH J L. Development of cam profiles using the convolution operator[J]. Journal of Mechanical Design, 1983,105(12):654-657.
[13] STODDART D A. Polydyne cam design-I[M]. New York: Machine Design, 1953: 121-164.
[14] SHIGLEY J E, UICKER J J. Theory of machines and mechanisms[M]. New York: Mcgrew-Hill, 1980: 204-207.
[15] MERMELSTEIN S P, ACAR M. Optimising cam motion using piecewise polynomials[J]. Engineering with Computers, 2004,19(4):241-254.
[16] QIU Hua, LIN Changjun, LI Ziye, et al. A universal optimal approach to cam curve design and it applica-tions[J]. Mechanism &. Machine Theory, 2005,40:669-692.
[17] NORTON R L. Cam design and manufacturing hand-book[M]. New York: Industrial press, 2002: 301-305.
[18] KENNEDY J, EBERHART R. Particle swarm optimization[C]// Proceeding IEEE international conference. Networks: IEEE, 1995: 1942-1948.
[19] BRAVO R, FLOCKER F W. Optimizing cam profiles using the particle swarm technique[J]. Journal of Mechanical Design, 2011,133(9):1-11.
[20] SHI Yuhui, EBERHART R. A modified particle swarm optimizer[C]//Proceedings of the IEEE conference on evolutionary computation. Anchorage: IEEE, 1998: 69-73.
[21] PEISEKAH E E. Improving the polydyne cam design method[J]. Russian Engineering Journal, 1966,12:25-27.
[22] ZHANG Zhongbo, JIANG Yunzhong, ZHANG Shuanghu, et al. An adaptive particle swarm optimization algorithm for reservoir operation optimization[J]. Applied Soft Computing, 2014,18:167-177.
[23] SUN Shiyuan, LI Jianwei. A two-swarm cooperative particle swarms optimization[J]. Swarm and Evolutionary Computation, 2014,15(4):1-18.
[24] 张雯雰, 王刚, 朱朝晖, 等. 粒子群优化算法种群规模的选择[J]. 计算机系统应用, 2010,19(5):125-128.
ZHANG Wenfen, WANG Gang, ZHU Zhaohui, et al. Population size selection of particle swarm optimizer algorithm[J]. Computer Systems & Applications, 2010,19(5):125-128.
[1] 袁汝旺, 祝雷雷, 吕雪奎, 杨佳敏. 旋转多臂变速运动规律建模及其对开口机构传动影响[J]. 纺织学报, 2019, 40(12): 127-133.
[2] 闫亦农 刘立枝 雒彬钰 崔慧荣. 基于粒子群算法的服装生产流水线编制[J]. 纺织学报, 2018, 39(10): 120-124.
[3] 金国光 魏晓勇 魏展 畅博彦 张旭阳. 旋转式多臂机提综机构动力学分析与优化[J]. 纺织学报, 2018, 39(09): 160-168.
[4] 张雷 苏宗帅 季祖鹏 顾萍萍. 共轭凸轮引纬机构的凸轮轮廓线光顺与反求[J]. 纺织学报, 2017, 38(12): 141-149.
[5] 尉苗苗 李岳阳 蒋高明 丛洪莲. 应用最优Gabor滤波器的经编织物疵点检测[J]. 纺织学报, 2016, 37(11): 48-54.
[6] 周远 徐映红 徐定华. 结合粒子群算法的一类双层纺织材料厚度设计反问题[J]. 纺织学报, 2013, 34(6): 40-45.
[7] 邱海飞 吴松林. 基于APDL的综框结构优化设计[J]. 纺织学报, 2013, 34(12): 122-0.
[8] 沈毅, 高大牛, 刘春雷. 基于ADMAS的GT421型多臂机机构动态仿真[J]. 纺织学报, 2012, 33(8): 119-123.
[9] 张增强;黄马壮. 粒子群算法在计算机自动配棉优化中的应用[J]. 纺织学报, 2011, 32(2): 44-47.
[10] 王永林;王东云. 织物变形舒适性的双群粒子群聚类研究[J]. 纺织学报, 2010, 31(4): 60-64.
[11] 李剑敏;沈毅;雷金锋. JAT610织机综框边杆的疲劳分析[J]. 纺织学报, 2005, 26(3): 66-68.
[12] 任家智;郁崇文. E62型精梳机分离罗拉传动机构工艺性能研究[J]. 纺织学报, 2004, 25(06): 32-33.
[13] 任家智;郁崇文. E7/6型精梳机钳板运动特性分析[J]. 纺织学报, 2004, 25(03): 30-31.
[14] 李伟. 片梭电子多臂机控制系统软件设计[J]. 纺织学报, 2002, 23(06): 57-59.
[15] 董学武;李建华;张启峰;陈光明;李玉华;靳桂荣. 新型织机综框的减振技术研究[J]. 纺织学报, 2002, 23(01): 40-42.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
京ICP备14006648号　 京公网安备11010502044800号
版权所有 © 2021 《纺织学报》编辑部
地址： 北京市朝阳区延静里中街3号主楼6层《纺织学报》杂志社　邮政编码：100025　
电话：010-65017711,65917740　传真：010-65016539　Email:fangzhixuebao@vip.126.com
本系统由北京玛格泰克科技发展有限公司设计开发