纺织学报 ›› 2013, Vol. 34 ›› Issue (1): 62-65.

• 染整与化学品 • 上一篇    下一篇

红麻纤维的化学脱胶工艺

张毅1,金关秀1,郁崇文2   

  1. 1. 浙江工业职业技术学院
    2. 东华大学纺织学院
  • 收稿日期:2011-12-27 修回日期:2012-04-25 出版日期:2013-01-15 发布日期:2013-01-07
  • 通讯作者: 张毅 E-mail:zhangyi851009@sina.com

Chemical degumming of kenaf

Guan-Xiu Jin2,Yu Chongwen   

  • Received:2011-12-27 Revised:2012-04-25 Online:2013-01-15 Published:2013-01-07

摘要: 由于红麻纤维木质素含量较高,脱胶工艺效果不佳,严重制约了人们对其的开发利用。本文通过预氧、碱煮、脱胶后处理(尿素浸泡和机械开松)工艺,运用化学与物理相结合的方法对红麻纤维进行脱胶加工,对影响脱胶效果的因子进行了探讨。试验结果表明:双氧水用量为10%(o.w.f),NaOH用量为6.5%(o.w.f)、Na2S用量为8%(o.w.f),煮练温度为95℃,煮练时间为140min,尿素浸泡时,质量浓度为3g/L时可达到最佳溶胀效果;机械开松前后,纤维细度(支数)提高了15%、断裂强度仅下降4.7%。经上述工艺可使红麻纤维断裂强度达到3.85 cN/dtex,细度(支数)可达738公支,其可纺性指标以及纤维品质均有明显改善,为后续纺纱利用奠定了基础。

关键词: 红麻纤维, 脱胶, 尿素, 机械开松, 性能

Abstract: Owing to the enriched lignin content of Kenaf, the poor effects of degumming process restricted its development and use seriously. Preoxidation, soda boiling, degumming process and final treatment (soaking in urea and mechanical loosening) were used, the degumming process were proceeded by both chemical and Physical method, and the effect factors of degumming process were discussed. The results indicate that the optimum technological parameter of degumming process are as follows: The dosage of H2O2 is 10% (o.w.f), NaOH is 6.5% (o.w.f133) and Na2S is 8% (o.w.f). Temperature of boiling-off is 95℃, and time is 140min. Dosage of mass concentration is 3g/L when soaking in urea. The maximum impact of swelling under these conditions can be obtained. And fineness of fibers improved 15%, while the breaking strength of fibers decreased only 4.7% after mechanical loosening. Breaking strength of fibers is up to 3.85cN/dtex, and fineness 738Nm under these conditions. Both the spinning property and the quality of fibers improved significantly, which can do some good to spinning process.

Key words: kenaf, degumming, urea, mechanical opening, property

中图分类号: 

  • TS102.221
[1] 李冻 陈太球 蒋春燕 傅佳佳 王鸿博. 原料及结构参数对防电弧织物性能的影响[J]. 纺织学报, 2018, 39(08): 41-45.
[2] 林启松 江力 汪凯 张顺花. 新型改性聚酯的制备及其性能[J]. 纺织学报, 2018, 39(08): 22-26.
[3] 陈萌 朱方龙 . 热辐射下织物内水分干燥实验及其动力学研究[J]. 纺织学报, 2018, 39(08): 52-57.
[4] 翟胜男 陈太球 蒋春燕 傅佳佳 王鸿博. 消防服外层织物热防护性与舒适性综合评价[J]. 纺织学报, 2018, 39(08): 100-104.
[5] 高党鸽 李亚娟 吕斌 马建中. 纳米银制备及其在纺织品中的应用研究进展[J]. 纺织学报, 2018, 39(08): 171-178.
[6] 朱金铭 钱建华 曹晨 曹原. 聚醚砜非织造布复合膜的空气过滤性能[J]. 纺织学报, 2018, 39(07): 55-62.
[7] 罗平艳 蒋金华 陈南梁 胡淳 崔鹏. 新型氟乙烯乙烯基醚树脂增强膜材料的制备及其力学性能[J]. 纺织学报, 2018, 39(07): 50-54.
[8] 王嘉欣 田秀枝 蒋学 王鸿博 高卫东. 二醛 β-环糊精/壳聚糖改性对涤纶织物亲水性能的影响[J]. 纺织学报, 2018, 39(07): 82-88.
[9] 陈洪立 焦晓宁 柯鹏. 取向增强复合锂离子电池隔膜的制备及其性能[J]. 纺织学报, 2018, 39(07): 8-14.
[10] 梁静 钟毅 毛志平 徐红 张琳萍 隋晓锋. 晶型对分散染料染色性能的影响[J]. 纺织学报, 2018, 39(07): 69-73.
[11] 王丽君 卢业虎 王帅 马妮妮. 形状记忆合金尺寸对消防服面料防护性能的影响[J]. 纺织学报, 2018, 39(06): 113-118.
[12] 金关秀 张毅 楼永平 祝成炎. 应用粗糙集和支持向量机的熔喷非织造布过滤性能预测[J]. 纺织学报, 2018, 39(06): 142-148.
[13] 张希文 武海良 沈艳琴 毛宁涛. 温湿度对涤/棉浆纱力学性能的影响[J]. 纺织学报, 2018, 39(06): 70-74.
[14] 刘慧慧 王云仪. 纸尿裤服用性能测评研究进展[J]. 纺织学报, 2018, 39(06): 175-182.
[15] 张寅江 王荣武 靳向煜. 湿法水刺可分散材料的结构与性能及其发展趋势[J]. 纺织学报, 2018, 39(06): 167-174.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!