纺织学报 ›› 2013, Vol. 34 ›› Issue (7): 121-125.

• 机械与器材 • 上一篇    下一篇

经编机梳栉的横移振动分析

张琦 夏风林 刘念 李怀宇 李萍 孙黎明   

  1. 江南大学经编技术教育部工程研究中心
  • 收稿日期:2012-07-02 修回日期:2013-02-28 出版日期:2013-07-15 发布日期:2013-07-15
  • 通讯作者: 夏风林 E-mail:xiafl_622@163.com
  • 基金资助:

    中央高校基本科研业务费专项资金资助项目;江苏省产学研联合创新资助项目;中国纺织工业联合会科技指导性项目

Analysis of shogging motion of guide bars on warp knitting machines

  • Received:2012-07-02 Revised:2013-02-28 Online:2013-07-15 Published:2013-07-15

摘要: 针对经编机高速运行时导纱梳桎因机械振动而产生擦针或擦伤纱线,并导致控制系统运行失效的问题,提出应用模态分析技术对经编导纱梳桎进行动力学分析。通过搭建声学振动测试平台,实测经编梳桎的关键动力学参数:阻尼比、固有频率和固有振型,获取反映梳桎单位激振力振幅响应的幅频特性,在此基础上提出经编梳桎高速运行时的减振措施,并经对比实验证明该措施有效,且梳桎振动分析方法正确可行。

关键词: 经编机, 梳栉, 横移运动, 振动测试, 减振措施

Abstract: According to the problem that the control system will operate failure because of the scratch between needles and yarn, when knitting machine running at a high speed and the guide bar shows extra mechanical vibration,this paper propose the method to analyze the dynamic character of guide bar with using modal analysis technology. Based on the building acoustic vibration test platform, analyzing the key kinetic parameters: damping ration, natural frequencies, natural vibration mode, amplitude and frequency response characteristics, the paper puts forward the effective measures of anti-vibration for warp knitting guide bar, and the contrast test results show that the measures are valid, and the vibration analysis method is feasible.

Key words: warp knitting machine, guide bar, shogging motion, vibration testing, anti-vibration measure

中图分类号: 

  • 中图分类号:TS 183.3
[1] 苏柳元 孟婥 张玉井 赵义满. 经编机梳栉横移系统误差建模与仿真[J]. 纺织学报, 2018, 39(08): 130-137.
[2] 郑静 夏风林 刘浪. 基于Simulink的经编机电子横移系统仿真[J]. 纺织学报, 2018, 39(02): 150-156.
[3] 牛善宇 曹清林. 采用电子凸轮的多梳栉经编机成圈运动[J]. 纺织学报, 2017, 38(04): 127-133.
[4] 赖森财 任雯 刘永桂. 嵌入式电子贾卡控制系统设计[J]. 纺织学报, 2016, 37(10): 135-140.
[5] 曹清林 赵红霞 曹娟娟 张大伟 樊腾飞. 浮纹贾卡经编机纱线选取机构的设计[J]. 纺织学报, 2016, 37(10): 130-134.
[6] 曹清林 黄骏 刘莉萍 刘志刚 朱晓宏 周金宇. 多梳栉经编机成圈机件的运动研究[J]. 纺织学报, 2014, 35(11): 139-0.
[7] 张琦 蒋高明 夏风林 刘苏 汤鲲鹏. 动态变结构控制策略在经编机高速电子横移中的应用[J]. 纺织学报, 2013, 34(3): 121-126.
[8] 刘鑫, 胡旭东, 陈洪立. 基于柔性多体系统的经编机梳栉摆动机构动力学分析[J]. 纺织学报, 2012, 33(6): 92-96.
[9] 郑宝平, 蒋高明, 夏风林, 张琦, 秦文. 双PID控制的经编机电子横移系统设计[J]. 纺织学报, 2012, 33(5): 135-139.
[10] 方园 夏凡甜 居婷婷. 基于UG的高速经编机槽针六连杆机构的建模[J]. 纺织学报, 2012, 33(12): 127-133.
[11] 蒋高明. 经编装备技术研究现状和发展趋势[J]. 纺织学报, 2012, 33(12): 140-144.
[12] 刘念 夏风林 张琦 蒋高明 殷明跃 秦文. 经编机梳栉横移机构的动力学分析[J]. 纺织学报, 2012, 33(11): 121-126.
[13] 曹清林. 经编机成圈主要运动分析及其实现机构[J]. 纺织学报, 2009, 30(11): 129-135.
[14] 夏风林;葛明桥;蒋高明. 高速经编机梳栉横移运动的优化设计[J]. 纺织学报, 2009, 30(05): 118-121.
[15] 夏风林. 伺服控制电子送经测速压辊的作用分析[J]. 纺织学报, 2008, 29(7): 95-99.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!