Journal of Textile Research ›› 2021, Vol. 42 ›› Issue (07): 95-100.doi: 10.13475/j.fzxb.20201000406

• Textile Engineering • Previous Articles     Next Articles

Design and numerical analysis of new types of melt blowing slot-dies

WANG Yudong1,2, JI Changchun1(), WANG Xinhou3, GAO Xiaoping4   

  1. 1. College of Biological and Chemical Engineering, Guangxi University of Science & Technology, Liuzhou, Guangxi 545006, China
    2. School of Mechanical Engineering, Xinjiang University, Urumqi, Xinjiang 830046, China
    3. College of Textiles, Donghua University, Shanghai 201620, China
    4. College of Textile and Light Industry, Inner Mongolia University of Technology, Hohhot, Inner Mongolia 010051, China
  • Received:2020-10-06 Revised:2021-04-04 Online:2021-07-15 Published:2021-07-22
  • Contact: JI Changchun E-mail:chuangchun_ji@163.com

RichHTML

28

PDF (PC)

85

Abstract:

In order to improve the airflow field and reduce the fiber diameter, several new die-heads were designed on the basis of a common slot-die, and a numerical study was conducted on such die-heads.The structural models of the new slot-dies were constructed by Gambit and Fluent software was used to numerically calculate the two-dimensional flow fields from these new slot-dies. In addition, the air velocity, temperature, turbulence intensity distribution on the spinning line of these new die-heads and their influence on fiber drafting were analyzed. The research results show that compared with the common slot-die, the new die-head with internal flow stabilizers can effectively reduce the recirculation zone, increase the peak speed on the spinning line, and reduce the speed fluctuation and temperature decay rate on the spinning line.The new slot-die with an air compressor can increase the velocity and temperature of the flow field, but it has little effect on the reverse velocity and the peak of the turbulence intensity near the die-head.Comprehensive comparison indicates that the new slot-die with an internal stabilizer and an air compressor has the best performance and is more conducive to drawing fibers.

Key words: melt blowing, slot-die, two-dimensional flow field, numeral simulation, drafting, melt blown nonwoven

CLC Number: 

  • TS174.1

Fig.1

Schematic diagram of common slot-die. (a) Cross-sectional view; (b) Top view"

Fig.2

Schematic diagram of slot-die 2. (a) Cross-sectional view;(b) Top view"

Fig.3

Schematic diagram of slot-die 3. (a) Cross-sectional view;(b) Top view"

Fig.4

Schematic diagram of slot-die 4. (a) Cross sectional view;(b) Top view"

Fig.5

Computational domain of slot-die 1"

Fig.6

Velocity distribution on spinning line"

Fig.7

Velocity vector near slot-die. (a) Slot-die 1;(b) Slot-die 2;(c) Slot-die 3;(d) Slot-die 4"

Fig.8

Temperature distribution on spinning line"

Fig.9

Turbulence intensity distribution on spinning line"

[1] HAN W L, BHAT G S, WANG X H. Investigation of nanofiber breakup in the melt-blowing process[J]. Industry & Engineering Chemistry Research, 2016, 55(11):3150-3156.
[2] 陈诗萍, 陈旻, 魏岑, 等. 医用防护服的构效特点及其研发趋势[J]. 纺织学报, 2020, 41(8):179-187.
CHEN Shiping, CHEN Min, WEI Cen, et al. Structure and functions of medical protective clothing and trend for research and development[J]. Journal of Textile Research, 2020, 41(8):179-187.
[3] 张星, 刘金鑫, 张海峰, 等. 防护口罩用非织造滤料的制备技术与研究现状[J]. 纺织学报, 2020, 41(3):168-174.
ZHANG Xing, LIU Jinxin, ZHANG Haifeng, et al. Preparation technology and research status of nonwoven filtration materials for individual protective masks[J]. Journal of Textile Research, 2020, 41(3):168-174.
[4] 张恒, 甄琪, 刘雍, 等. 嵌入式聚丙烯/聚乙二醇微纳米纤维材料的结构特征及其气固过滤性能[J]. 纺织学报, 2019, 40(9):28-34.
ZHANG Heng, ZHEN Qi, LIU Yong, et al. Air filtration performance and morphological features of polyethylene glycol/polypropylene composite fibrous materials with embedded structure[J]. Journal of Textile Research, 2019, 40(9):28-34.
[5] HARPHAM A S, SHAMBAUGH R L. Flow field of practical dual rectangular jets[J]. Industry & Engineering Chemistry Research, 1996, 35(10):3776-3781.
[6] HARPHAM A S, SHAMBAUGH R L. Velocity and temperature fields of dual rectangular jets[J]. Industry & Engineering Chemistry Research, 1997, 36:3937-3943.
[7] WANG X M, KE Q F. Empirical formulas for distributions of air velocity and temperature along the spinline of a dual slot die[J]. Polymer Engineering and Science, 2005, 45(8):1092-1097.
[8] XIE S, ZENG Y C. Turbulent air flow field and fiber whipping motion in the melt blowing process: experimental study[J]. Industry & Engineering Chemistry Research, 2012, 51:5346-5352.
[9] XIE S, HAN W L, JIANG G J, et al. Turbulent air flow field in slot-die melt blowing for manufacturing microfibrous nonwoven materials[J]. Journal of Material Science, 2018, 53:6991-7003.
doi: 10.1007/s10853-018-2008-y
[10] KRUTKA H M, SHAMBAUGH R L, PAPAVASSILIOU D V. Analysis of a melt-blowing die: comparison of CFD and experiments[J]. Industrial & Engineering Chemistry Research, 2002, 41(20):5125-5138.
doi: 10.1021/ie020366f
[11] CHEN T, WANG X H, HUANG X B. Modeling the air-jet flow field of a dual slot die in the melt-blowing nonwoven process[J]. Textile Research Journal, 2004, 74(11):1018-1024.
doi: 10.1177/004051750407401114
[12] XIN S F, WANG X H. Investigation into the effect of the angle of dual slots on an air flow field in melt blowing via numerical simulation[J]. E-Polymers, 2016, 16:337-342.
doi: 10.1515/epoly-2016-0057
[13] SUN Y F, WANG X H. Optimal geometry design of the melt blowing slot die via the orthogonal array method and numerical simulation[J]. Journal of The Textile Institute, 2011, 102(1):65-69.
doi: 10.1080/00405000903475805
[14] SUN Y F, WANG X H. Optimization of air flow field of the melt blowing slot die via numerical simulation and genetic algorithm[J]. Journal of Applied Polymer Science, 2010, 115(3):1540-1545.
doi: 10.1002/app.v115:3
[15] 辛三法, 王新厚, 胡守忠. 双槽熔喷工艺中外沿长度对空气流场的影响[J]. 纺织学报, 2015, 36(4):71-75.
XIN Sanfa, WANG Xinhou, HU Shouzhong. The effect of outer length on air flow field in melt blowing with dual slots was studied via numerical simulation[J]. Journal of Textile Research, 2015, 36(4):71-75.
[16] WANG Y D, WANG X H. Numerical analysis of new modified melt-blowing dies for dual rectangular jets[J]. Polymer Engineering and Science, 2014, 54(1):110-116.
doi: 10.1002/pen.23536
[17] 孙亚峰. 微纳米纤维纺丝拉伸机理的研究[D]. 上海: 东华大学, 2010: 25-45.
SUN Yafeng. Investigation of micro nano fiber formation[D]. Shanghai: Donghua University, 2010: 25-45.
[18] 姬长春, 张开源, 王玉栋, 等. 熔喷三维气流场的数值计算与分析[J]. 纺织学报, 2019, 40(8):175-180.
JI Changchun, ZHANG Kaiyuan, WANG Yudong, et al. Numerical calculation and analysis of three-dimensional flow field in melt-blown process[J]. Journal of Textile Research, 2019, 40(8):175-180.
[19] LAUNDER B E, SPALDING D B. Lectures in mathematical models of turbulence[M]. London: Academic Press, 1972: 55.
[20] BANSAL V, SHAMBAUGH R L. On-line determination of diameter and temperature during melt blowing of polypropylene[J]. Industrial & Engineering Chemistry Research, 1998, 37(5):1799-1806.
doi: 10.1021/ie9709042
[1] HE Yaqin, BI Xuerong, QIAN Xixi, RUAN Jun, YU Chongwen. Simulation study on effect of drafting on sliver unevenness [J]. Journal of Textile Research, 2021, 42(06): 85-90.
[2] ZHEN Qi, ZHANG Heng, ZHU Feichao, SHI Jianhong, LIU Yong, ZHANG Yifeng. Fabrication and properties of polypropylene/polyester bicomponent micro-nanofiber webs via melt blowing process [J]. Journal of Textile Research, 2020, 41(02): 26-32.
[3] WEI Yanhong, XIE Chunping, LIU Xinjin, SU Xuzhong, YIN Gaowei. Drafting mechanism and application of spun yarn produced by large diameter soft rubber-covered roll [J]. Journal of Textile Research, 2019, 40(10): 62-67.
[4] . Review on processes of nanofiber prepared by polymer melt method [J]. Journal of Textile Research, 2018, 39(12): 166-174.
[5] . Prediction on filtration performance of melt blown nonwoven fabric based on rough set theory and support vector machine [J]. JOURNAL OF TEXTILE RESEARCH, 2018, 39(06): 142-148.
[6] . Design and optimization of partial parameters of main drafting for FA322B drawing frame [J]. JOURNAL OF TEXTILE RESEARCH, 2017, 38(08): 139-143.
[7] . Double S curves soft drafting technology [J]. JOURNAL OF TEXTILE RESEARCH, 2017, 38(07): 34-38.
[8] . Simulation and verification of fiber deameter re-increasing in melt blowing process [J]. JOURNAL OF TEXTILE RESEARCH, 2017, 38(04): 17-21.
[9] . Simulating design for draft ratio of back drafting zone on drawing frame [J]. JOURNAL OF TEXTILE RESEARCH, 2017, 38(04): 39-45.
[10] . Roller-drafting model based on discrete-event simulation [J]. Journal of Textile Research, 2016, 37(2): 125-132.
[11] . Study o yarn unevenness based on experiment of fibers acclilrated-point distribution [J]. JOURNAL OF TEXTILE RESEARCH, 2016, 37(08): 32-36.
[12] . Design of surface and inner layer exchangeable fabric by using color effect [J]. Journal of Textile Research, 2015, 36(12): 42-46.
[13] . Manufacture technology of micro-nano fiber by melt blowing [J]. Journal of Textile Research, 2015, 36(07): 7-11.
[14] . Influence of outer length on air flow field in melt blowing with dual slots [J]. Journal of Textile Research, 2015, 36(04): 71-75.
[15] . Preparation and performance of biodegradable slice of poly (propylene carbonate) / polypropylene for nonwoven fabrics [J]. JOURNAL OF TEXTILE RESEARCH, 2013, 34(7): 15-21.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
京ICP备14006648号
Copyright 2021 © Editorial office of Journal of Textile Research
Supported by Beijing Magtech Co.Ltd