Journal of Textile Research ›› 2019, Vol. 40 ›› Issue (01): 114-119.doi: 10.13475/j.fzxb.20180305906

• Apparel Engineering • Previous Articles     Next Articles

Three-dimensional on-site scanning measurement and characterization of air gap entrapped between flame manikin and clothing

WANG Min1,2, LI Jun1,2()   

  1. 1. College of Fashion and Design, Donghua University, Shanghai 200051, China
    2. Key Laboratory of Clothing Design and Technology, Ministry of Education, Donghua University, Shanghai 200051, China
  • Received:2018-03-23 Revised:2018-09-26 Online:2019-01-15 Published:2019-01-18
  • Contact: LI Jun E-mail:lijun@dhu.edu.cn

RichHTML

4

PDF (PC)

278

Abstract:

In order to accurately acquir the air gap thickness and distribution of fireproof clothing before and after heat exposure in the flame manikin test, a measurement and characterization method based on three-dimensional (3-D) on-site scanning was proposed. Firstly, by using Kinect depth cameras, a 3-D scanning platform was established in the combustion chamber, based on which the 3-D point cloud data of the nude manikin and clothed manikin before and after exposure was obtained directly. Then by modeling, alignment, and 3-D comparison in the reverse engineering software Geomagic, and with the realization of accurate location of the manikin surface sensors in the 3-D space, the air gap thickness and distribution were extracted quickly and effectively. The verification test results show that even for the same clothes, the distribution of air gaps under clothing is quite different each time. The variation coefficients of the gap thickness at the back before and after exposure even reach 46% and 35%, respectively. This indicates that the data obtained from the previous remote scanning method an not fully reflect the real state in the combustion test, and the on-site scanning is more conducive to accurately analyze the influence of air thickness change caused by clothing material, specifications, thermal shrinkage and other factors on the thermal protective performance.

Key words: thermal protective, 3-D on-site scanning, flame manikin, air gap thickness

CLC Number: 

  • TS941.17

Fig.1

Construction of Microsoft Kinect device"

Fig.2

Body scanner installed in flame chamber."

Fig.3

Sensor location of the flame manikin."

Fig.4

Photos and reconstructed 3-D models of flame manikin."

Tab. 1

Average gap size and change rate before and after exposure"

重复样本 A1/mm A2/mm R/%
样本1 24.76 9.80 60.42
样本2 24.41 9.98 59.12
样本3 23.52 9.80 58.33
平均值 24.23 9.86 59.29
变异系数 2.64% 1.05% 1.78%

Fig.5

Distribution of air gap under clothing."

Tab.2

Local air gap thickness and reduction of garment before and after exposure"

传感器
编号		 样本1 样本2 样本3 变异系数/%
A1/mm A2/mm R/% A1/mm A2/mm R/% A1/mm A2 R/% A1 A2 R
B01 26.59 6.81 74.39 33.89 10.27 69.7 15.58 7.75 50.26 36.36 21.62 19.75
B02 16.44 8.79 46.53 28.66 9.65 66.33 12.71 10.85 14.63 43.30 10.60 61.37
B03 16.33 3.50 78.57 19.38 4.52 76.68 13.36 4.70 64.82 18.40 15.26 10.16
B04 23.35 3.55 84.8 17.05 5.42 68.21 7.79 5.16 33.76 48.72 21.51 41.82
B05 40.61 6.55 83.87 53.58 10.65 80.12 48.86 4.99 89.79 13.77 39.52 5.76
B06 15.59 0.42 97.31 16.13 0.55 96.59 18.39 0.42 97.72 8.89 16.20 0.59
B07 23.27 2.16 90.72 13.99 3.87 72.34 10.07 1.45 85.6 42.97 49.89 11.45
B08 25.57 2.40 90.61 46.02 4.82 89.53 35.12 3.12 91.12 28.77 36.05 0.90
B09 28.22 2.11 92.52 33.25 5.50 83.46 46.97 4.39 90.65 26.85 43.21 5.38
B10 21.58 0.42 98.05 32.11 1.82 94.33 29.61 0.48 98.38 19.81 87.30 2.32
B11 1.55 0.42 72.9 18.63 1.19 93.61 8.03 0.89 88.92 91.70 46.57 12.75
B12 41.31 0.88 97.87 36.45 2.59 92.89 38.31 2.03 94.70 6.34 47.55 2.65
B13 11.49 0.59 94.87 35.55 0.42 98.82 27.69 0.42 98.48 49.25 20.59 2.25
B14 32.15 1.90 94.09 18.87 2.67 85.85 15.10 3.28 78.28 40.64 26.43 9.19
B15 0.54 0.46 14.81 24.40 0.84 96.56 0.42 0.42 0.00 163.37 40.43 140.07
B16 7.01 0.83 88.16 3.89 1.59 59.13 4.47 1.38 69.13 32.39 30.98 20.45
B17 1.49 0.60 59.73 7.80 1.82 76.67 0.42 1.34 -219.05 123.21 49.04 -602.77
[1] KIM Y, LEE C, LI P, et al. Investigation of air gaps entrapped in protective clothing systems[J]. Fire and Materials, 2002,26(3):121-126.
doi: 10.1002/(ISSN)1099-1018
[2] SONG G W. Clothing air gap layers and thermal resistance performance in single layer garment[J]. Journal of Industrial Textiles, 2007,36(3):193-205.
doi: 10.1177/1528083707069506
[3] MAH T, SONG G W. Investigation of the contribution of garment design to thermal protection: part 1: characterizing air gaps using three-dimensional body scanning for women's protective clothing[J]. Text Research Journal, 2010,80(13):1317-1329.
doi: 10.1177/0040517509358795
[4] MAH T, SONG G W. Investigation of the contribution of garment design to thermal protection: part 2: instrumented female mannequin flash-fire evaluation system[J]. Textile Research Journal, 2010,80(14):1473-1487.
doi: 10.1177/0040517509358796
[5] 王云仪, 张雪, 李小辉, 等. 基于Geomagic 软件的燃烧假人衣下空气层特征提取[J]. 纺织学报, 2012,33(11):102-106.
WANG Yunyi, ZHANG Xu, LI Xiaohui, et al. Geomagic-based characteristic extraction of air gap under clothing[J]. Journal of Textile Research, 2012,33(11):102-106.
[6] ZOLLHOFER M, MARTINEK M, GREINER G, et al. Automatic reconstruction of personalized avatars from 3D face scans[J]. Computer Animation and Virtual Worlds, 2011,22(2/3):195-202.
doi: 10.1002/cav.v22.2/3
[7] 周瑾. 基于 Kinect 深度相机的三维人体重建技术研究[D]. 杭州:杭州电子科技大学, 2013: 10-22.
ZHOU Jin. Research on 3D human body reconstruction technology based on the Kinect depth camera[D]. Hangzhou:Hangzhou University of Electronic Science and Technology, 2013: 10-22.
[8] 宋诗超, 禹素萍, 许武军. 基于Kinect的三维人体扫描、重建及测量技术的研究[J]. 天津工业大学学报, 2012,31(5):34-41.
SONG Shichao, YU Suping, XU Wujun. Research on 3D human scanning, reconstruction and measurement technology based on Kinect[J]. Journal of Tianjin University of Technology, 2014,31(5):34-41.
[9] 王敏, 李小辉. 我国建成国际领先的服装燃烧假人系统:“东华火人”[J]. 中国个体防护装备, 2011(5):54-55.
WANG Min, LI Xiaohui. The latest flame test manikin system developed in China[J]. China Personal Protective Equipment, 2011(5):54-55.
[10] PSIKUTA A, FRACKIEWICZ-KACZMAREK J, FRYDRYCH I, et al. Quantitative evaluation of air gap thickness and contact area between body and garment[J]. Textile Research Journal, 2012,82(14):1405-1413.
doi: 10.1177/0040517512436823
[1] ZHAI Li′na, LI Jun, YANG Yunchu. Development and current state of thermal sensors used for testing thermal protective clothing [J]. Journal of Textile Research, 2020, 41(10): 188-196.
[2] HE Jiazhen, XUE Xiaoyu, WANG Min, LI Jun. Predicting thermal protective performance of clothing based on maximum attenuation factor model [J]. Journal of Textile Research, 2020, 41(06): 112-117.
[3] GAO Shan, LU Yehu, ZHANG Desuo, WU Lei, WANG Laili. Thermal protective performance of composite flame retardant fabrics treated by graphene aerogel [J]. Journal of Textile Research, 2020, 41(04): 117-122.
[4] DING Ning, LIN Jie. Free convection calculation method for performance prediction of thermal protective clothing in an unsteady thermal state [J]. Journal of Textile Research, 2020, 41(01): 139-144.
[5] QIU Hao, SU Yun, WANG Yunyi. Influence of steam exposure condition on thermal protective performance of fabrics [J]. Journal of Textile Research, 2020, 41(01): 118-123.
[6] HU Beibei, DU Feifei, LI Xiaohui. Hole structure optimization and evaluation of thermal barrier for firefighter protective clothing [J]. Journal of Textile Research, 2019, 40(11): 140-144.
[7] WANG Lu, DING Xiaojun, XIA Xin, WANG Hong, ZHOU Xiaohong. Protective function of SiO2 aerogel hybrid / aramid nonwovens fabric [J]. Journal of Textile Research, 2019, 40(10): 79-84.
[8] ZHANG Hongyue, LI Xiaohui. Evaluation on radiation thermal performance of honeycomb sandwich structure of thermal protective clothing fabrics [J]. Journal of Textile Research, 2019, 40(10): 147-151.
[9] . Prediction of skin injury degree based on modified model of heat transfer in three-layered thermal protective clothing [J]. JOURNAL OF TEXTILE RESEARCH, 2018, 39(01): 111-118.
[10] . Research progress on air gap entrapped in firefighters' protective clothing and its measurement methods [J]. JOURNAL OF TEXTILE RESEARCH, 2017, 38(06): 151-156.
[11] . Influence of waterproof permeable layer on thermal and moisture protective performance of firefighter protective clothing in fire disaster [J]. JOURNAL OF TEXTILE RESEARCH, 2017, 38(02): 152-158.
[12] . Effects of light and moisture on performance of fabrics for firefighter protective clothing [J]. JOURNAL OF TEXTILE RESEARCH, 2015, 36(09): 82-88.
[13] . Evaluation of thermal protective performance of fabric for firefighter protective clothing [J]. JOURNAL OF TEXTILE RESEARCH, 2015, 36(08): 110-115.
[14] . Devilopment and current status on performance test and evaluation of thermal protective clothing [J]. JOURNAL OF TEXTILE RESEARCH, 2015, 36(07): 162-168.
[15] . Application and feasibility analysis of phase change materials for fire-fighter suit [J]. JOURNAL OF TEXTILE RESEARCH, 2014, 35(8): 124-0.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
京ICP备14006648号
Copyright 2021 © Editorial office of Journal of Textile Research
Supported by Beijing Magtech Co.Ltd