纺织学报 ›› 2016, Vol. 37 ›› Issue (08): 154-159.

• 管理与信息化 • 上一篇    下一篇

采用网络控制的电脑横机CAN总线调度仿真

  

  • 收稿日期:2015-01-05 修回日期:2016-04-28 出版日期:2016-08-15 发布日期:2016-08-05

CAN Bus scheduling simulation for computerized flat knitting machine based on network control

  • Received:2015-01-05 Revised:2016-04-28 Online:2016-08-15 Published:2016-08-05

摘要:

为满足电脑横机控制器网络化发展方向的要求,在分析传统电脑横机单机控制器的基础上,提出了基于双电脑横机控制器的CAN总线的调度仿真方法,并设计了1 台电脑控制器同时控制2台电脑横机的“PC+节点”的网络控制结构。通过将电脑横机控制系统中的电动机、电磁控制器和传感器等部件等效为网络控制系统中的网络节点,并利用MatLab数学软件中的Truetime工具箱,按照双电脑控制器的网络结构,建立基于CAN总线的网络化电脑横机的仿真模型。并对CAN总线的动态调度算法和混合调度算法性能进行仿真对比,得出混合调度算法可满足网络化电脑横机控制系统要求的结论,验证了利用CAN总线构成的网络化电脑横机控制器的可行性。

关键词: 电脑横机, 网络控制系统, CAN总线, 调度算法

Abstract:

In order to meet the development requirements of the network control of computerized flat knitting machine, a kind of high-speed CAN bus network control system for computerized flat knitter is proposed based on the traditional stand-alone controller, and a network control structure of the "PC+ nodes" is designed to use in the computer controller, which can control two flat knitting machines at the same time. The components of flat knitting machine, including motors, electromagnetic controllers and sensors are equivalent to the network nodes. According to the network structure of two machine’s controllers, the simulation model of the network computer flat knitting machine based on CAN bus is established by Truetime toolbox in Matlab software. Based on the model, by simulating and comparing the dynamic priority scheduling algorithm and hybrid scheduling algorithm, it concludes that the hybrid scheduling algorithm fits the computerized flat knitter network control system, which verify the feasibility of the network controller of computerized flat knitting machine based on CAN bus.

Key words: computerized flat knitting machine, network control system, CAN bus, scheduling algorithm

[1] 邱庄岩 花芬 吴志明. 四针床全成形编织工艺及其应用[J]. 纺织学报, 2018, 39(08): 63-70.
[2] 彭佳佳 蒋高明 丛洪莲 王敏. 全成形毛衫的结构与编织原理[J]. 纺织学报, 2017, 38(11): 48-55.
[3] 王敏 丛洪莲 蒋高明 彭佳佳. 四针床电脑横机的全成形工艺[J]. 纺织学报, 2017, 38(04): 61-67.
[4] 李晓英 蒋高明 马丕波 聂小林. 三维横编间隔织物的编织工艺及其性能[J]. 纺织学报, 2016, 37(07): 66-70.
[5] 胡旭东 黄肖华 彭来湖. 内嵌驱动针织机械密度调节装置的研制[J]. 纺织学报, 2015, 36(07): 131-135.
[6] 胡旭东 黄栋明 彭来湖. 超多机头绣花机自动换底线系统设计[J]. 纺织学报, 2015, 36(04): 134-0.
[7] 陈景波 华强 周平 浦炜 卢达. 高性能电脑横机纱嘴控制方法的设计与实现[J]. 纺织学报, 2013, 34(10): 137-0.
[8] 方园 夏凡甜. 基于UG NX/Motion的电脑横机成圈机构建模与仿真[J]. 纺织学报, 2013, 34(1): 122-127.
[9] 张弛, 张成俊, 吴晓光. 电脑横机控制系统数据准备[J]. 纺织学报, 2012, 33(8): 124-129.
[10] 陈景波;卢达;王玲玲. 全自动电脑横机上位机软件的设计[J]. 纺织学报, 2011, 32(2): 131-135.
[11] 王继曼;宋广礼. 电脑横机编织工时的预测[J]. 纺织学报, 2010, 31(5): 48-54.
[12] 吴朝阳;苏俊;陈淑侠;芮延年. HR-I电子提花机控制器的设计[J]. 纺织学报, 2010, 31(3): 115-118.
[13] 罗治平;丁浩;张永宇. 移圈针沟槽的加工工艺[J]. 纺织学报, 2010, 31(10): 129-133.
[14] 孙华平;卢达. 灵敏度可调的电脑横机震动保护设计[J]. 纺织学报, 2009, 30(9): 119-122.
[15] 金玉珍;吴震宇;武传宇;韩涛;胡旭东;朱祖超. 基于CAN总线喷气织机控制系统的研制[J]. 纺织学报, 2009, 30(02): 117-120.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!