Journal of Textile Research ›› 2020, Vol. 41 ›› Issue (12): 81-86.doi: 10.13475/j.fzxb.20200307106

• Dyeing and Finishing & Chemicals • Previous Articles     Next Articles

Research on forming process of bulge at start of jet printing conductive circuit on fabric surfaces

XIAO Yuan1,2(), WANG Pan1, ZHANG Wei1, ZHANG Chengkun1   

  1. 1. School of Mechanical and Electrical Engineering, Xi'an Polytechnic University, Xi'an, Shaanxi 710048, China
    2. Xi'an Key Laboratory of Modern Intelligent Textile Equipment, Xi'an Polytechnic University, Xi'an, Shaanxi 710600, China
  • Received:2020-03-27 Revised:2020-08-30 Online:2020-12-15 Published:2020-12-23

RichHTML

2

PDF (PC)

91

Abstract:

In order to improve the forming quality of the conductive circuit on a fabric surface printed by the microdroplet jet printing technique, a high-speed camera was used to capture the process of droplet-jet printing conductive circuit in view of the bulged deposition lines at the start. The dynamic changes of left and right contact angles during the fusion oscillation between droplet, the fusion of droplet with the circuits and the process of transporting liquid to the starting of the line were studied according to the bulge elimination scheme. The results show that during the oscillation process of droplets coalescence, the oscillation trend towards the starting end is always greater than the other end, causing continuous expansion of the substrate wetting area at start of the printing circuit. After the droplets contact the circuit, part of the liquid wets the substrate to extend the length of the circuit, and the rest of the liquid is transported to the starting of the circuit at a constant speed to form a bulge. The surface of the fabric moistened with the ascorbic acid solution eliminates the bulging at the start of the forming circuit, leading to formation of expected uniform dimension of the deposited lines.

Key words: intelligent textile, microdroplet jetting, conductive circuit, deposition formation, bulge at start

CLC Number: 

  • TH16

Fig.1

Pneumatic droplet-jet printing deposition system"

Fig.2

Droplet coalescence process at start of circuit"

Fig.3

Schematic diagram of mass center position and substrate wetting area"

Fig.4

Left and right contact angle measurement diagram"

Fig.5

Left and right contact angle changes at droplet coalescence process"

Fig.6

Process of microdrop jet printing on a fabric"

Fig.7

Schematic diagram of circuit surface profile measurement"

Fig.8

Change process of x1, x2, x3 point profile in circuit with time"

Fig.9

Time for first reach maximl height of each position on circuit"

Fig.10

SEM image (a) and EDS diagram (b) of shaped circuit"

[1] 李思明, 吴官正, 胡雨洁, 等. 压力分布监测袜的制备及其传感性能[J]. 纺织学报, 2019,40(7):138-144.
LI Siming, WU Guanzheng, HU Yujie, et al. Preparation of pressure distribution monitoring socks and related sensing properties[J]. Journal of Textile Research, 2019,40(7):138-144.
[2] BHUVANESHWARI B, PRADEEP N, KUMAR P, et al. Smart army jacket[J]. Perspectives in Communication, Embedded-systems and Signal-Processing, 2019,2(10):241-244.
[3] FERNÁNDEZ-CARAMÉS T, FRAGA-LAMAS P. Towards the internet-of-smart-clothing: a review on iot wearables and garments for creating intelligent connected e-textiles[J]. Electronics, 2018,7(12):405.
[4] 杨晨啸, 李鹂. 柔性智能纺织品与功能纤维的融合[J]. 纺织学报, 2018,39(5):160-169.
YANG Chenxiao, LI Li. Integration of soft intelligent textile and functional fiber[J]. Journal of Textile Research, 2018,39(5):160-169.
[5] GHAHREMANI H M, LATIFI M. Overview of wearable electronics and smart textiles[J]. The Journal of The Textile Institute, 2017,108(4):631-652.
[6] 谢丹, 张鸿海, 舒霞云, 等. 气动膜片式微滴喷射装置理论分析与实验研究[J]. 中国机械工程, 2012,23(14):1732-1737.
XIE Dan, ZHANG Honghai, SHU Xiayun, et al. Theoretical analysis and experimental research on pneumatically diaphragm-driven drop-on-demand inkjet generator[J]. China Mechanical Engineering, 2012,23(14):1732-1737.
[7] 李素丽, 魏正英, 杜军, 等. 基于金属3D打印技术成形嵌套零件工艺研究[J]. 材料科学与工艺, 2016,24(6):1-7.
LI Suli, WEI Zhengying, DU Jun, et al. Research of 3D printing technology based on metal double nozzle to form the hanging parts[J]. Materials Science and Technology, 2016,24(6):1-7.
doi: 10.1179/174328407X245779
[8] NEGRO A, CHERBUIN T, LUTOLF M P. 3D inkjet printing of complex, cell-laden hydrogel structures[J]. Scientific Reports, 2018,8(1):17099.
pmid: 30459444
[9] JALKANEN T, MÄKILÄ E, MÄÄTTÄNEN A, et al. Porous silicon micro- and nanoparticles for printed humidity sensors[J]. Applied Physics Letters, 2012,101(26):263110-263114.
[10] 张楠, 林健, 王同举, 等. 用于打印柔性导线的液态金属微滴制备过程研究[J]. 电子元件与材料, 2018,37(7):1-7.
ZHANG Nan, LIN Jian, WANG Tongju, et al. Formation process of liquid metal droplets using for printing flexible conductive wires[J]. Electronic Components and Materials, 2018,37(7):1-7.
[11] DUINEVELD P C. The stability of ink-jet printed lines of liquid with zero receding contact angle on a homogeneous substrate[J]. Journal of Fluid Mechanics, 2003,477:175-200.
[12] SCHIAFFINO S, SONIN A A. Formation and stability of liquid and molten beads on a solid surface[J]. Journal of Fluid Mechanics, 1997,343:95-110.
[13] STRINGER J, DERBY B. Formation and stability of lines produced by inkjet printing[J]. Langmuir, 2010,26(12):10365-10372.
doi: 10.1021/la101296e pmid: 20481461
[14] LEE S H, CHO Y J. Characterization of silver inkjet overlap-printing through cohesion and adhesion[J]. Journal of Electrical Engineering and Technology, 2012,7(1):91-96.
[15] LIAN H, QI L, LUO J, et al. Uniform nitrogen-doped graphene lines with favorable outlines printed by elaborate regulation of drying and overlapping[J]. Applied Surface Science, 2019,473:614-621.
doi: 10.1016/j.apsusc.2018.12.176
[16] 王春晖. 基于微流体数字化喷射技术的直写导线技术研究[D]. 南京: 南京理工大学, 2006: 41-49.
WANG Chunhui. Research on the technology of direct write wire based on microfluidic digital jet tech-nology[D]. Nanjing: Nanjing University of Science and Technology, 2006: 41-49.
[17] 肖渊, 尹博, 李岚馨, 等. 微滴喷射化学沉积工艺条件对成形银导线的影响[J]. 纺织学报, 2019,40(5):78-83.
XIAO Yuan, YIN Bo, LI Lanxin, et al. Influence of process conditions on silver conductive lines by micro-droplet jet printing solution reaction[J]. Journal of Textile Research, 2019,40(5):78-83.
[18] CASTREJON-PITA J R, BETTON E S, KUBIAK K J, et al. The dynamics of the impact and coalescence of droplets on a solid surface[J]. Biomicrofluidics, 2011,5(1):014112.
[19] BERKER R A. Intégration des équations du mouvement d'un fluide visqueux incompressible[M]. Berlin: Handbuch der Physik, 1963,3:1-34.
[1] MA Liyun, WU Ronghui, LIU Sai, ZHANG Yuze, WANG Jun. Preparation and electrical properties of triboelectric nanogenerator based on wrapped composite yarn [J]. Journal of Textile Research, 2021, 42(01): 53-58.
[2] YANG Yuchen, QIN Xiaohong, YU Jianyong. Research progress of transforming electrospun nanofibers into functional yarns [J]. Journal of Textile Research, 2021, 42(01): 1-9.
[3] WANG Jilong, LIU Yan, JING Yuanyuan, XU Qingli, QIAN Xiangyu, ZHANG Yihong, ZHANG Kun. Advances in fiber-based wearable electronic devices [J]. Journal of Textile Research, 2020, 41(12): 157-165.
[4] CHEN Hui, WANG Xi, DING Xin, LI Qiao. Design of temperature-sensitive garment consisting of full fabric sensing networks [J]. Journal of Textile Research, 2020, 41(03): 118-123.
[5] WU Ronghui, MA Liyun, ZHANG Yifan, LIU Xiangyang, YU Weidong. Strain sensor based on silver nanowires coated yarn with chain stitch structure [J]. Journal of Textile Research, 2019, 40(12): 45-49.
[6] LI Siming, WU Guanzheng, HU Yujie, FANG Meiqi, HE Luxiang, HE Yan, XIAO Xueliang. Preparation of pressure distribution monitoring socks and related sensing properties [J]. Journal of Textile Research, 2019, 40(07): 138-144.
[7] . Big-data-driven framework for intelligent textile manufacturing [J]. JOURNAL OF TEXTILE RESEARCH, 2017, 38(10): 159-165.
[8] . Experimental research on deposition process of micro-droplet jet printing on fabric surface [J]. JOURNAL OF TEXTILE RESEARCH, 2017, 38(05): 139-144.
[9] HUANG He;YU Weidong;YAN Haojing. Classification of self-adaptive textiles and related products [J]. JOURNAL OF TEXTILE RESEARCH, 2007, 28(12): 135-140.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
京ICP备14006648号
Copyright 2021 © Editorial office of Journal of Textile Research
Supported by Beijing Magtech Co.Ltd