纺织学报 ›› 2019, Vol. 40 ›› Issue (05): 59-63.doi: 10.13475/j.fzxb.20180403405

• 纺织工程 • 上一篇    下一篇

玻璃纤维/环氧树脂基夹芯材料侧压性能数值模拟

曹海建1(), 陈红霞2, 黄晓梅1   

  1. 1.南通大学 纺织服装学院, 江苏 南通 226019
    2.南通大学 分析测试中心, 江苏 南通 226019
  • 收稿日期:2018-04-16 修回日期:2019-02-15 出版日期:2019-05-15 发布日期:2019-05-21
  • 作者简介:曹海建(1979—),男,副教授,博士。主要研究方向为纤维复合材料的开发与应用。E-mail:caohaijian @ntu.edu.cn。
  • 基金资助:
    国家重点研发计划项目(2018YFC0810300);江苏省“六大人才高峰”高层次人才项目(XCL-061);江苏省高校自然科学研究项目(18KJA430011);江苏省先进纺织工程技术中心开放基金重大项目(XJFZ/2018/02)

Numerical simulation of side compressive properties on glass fiber/epoxy resin sandwich composite

CAO Haijian1(), CHEN Hongxia2, HUANG Xiaomei1   

  1. 1. School of Textile and Clothing, Nantong University, Nantong, Jiangsu 226019, China
    2. Analysis & Testing Center, Nantong University, Nantong, Jiangsu 226019, China
  • Received:2018-04-16 Revised:2019-02-15 Online:2019-05-15 Published:2019-05-21

RichHTML

1

PDF (PC)

62

摘要：

为分析材料在侧压载荷下的失效机制及破坏模式,采用有限元软件ANSYS,建立了材料的细观结构模型,并进行侧压性能的数值模拟,探讨了材料在3 mm侧压位移载荷作用下复合材料、纤维和树脂基体的应力、应变分布情况。结果表明:玻璃纤维/环氧树脂基夹芯材料在侧压载荷作用下,从宏观角度分析发现,上下面板应力最大,最易发生压缩破坏;芯材应力最小,最不易被破坏;2排芯材间的面板最易发生失稳破坏,这是导致材料失效的最主要原因。从微观角度分析发现,纤维起主要承载作用,树脂起次要作用,当侧压位移载荷达到3 mm时,材料的破坏模式主要为树脂破裂、纤维与树脂严重脱黏等。

关键词: 玻璃纤维/环氧树脂基夹芯材料, 数值模拟, 侧压性能, 失效机制, 破坏模式

Abstract:

In order to reveal failure mechanism and failure mode of glass fiber/epoxy resin sandwich composite under side compressive load, a meso-structural model was built by using the finite element software ANSYS, and numerical simulation of side compressive properties on the composite was analyzed emphasisly. The stress and strain distribution of the composite, fibers and resin was discussed under side compressive loads of 3 mm displacement by using the meso-structural model. The results show that when the composite is subjected to side compressive load, the maximum value of stress occurs on the upper and lower face-sheet macroscopically, where the composite is damaged easily. The minimum value of stress occurs on the piles, where the composite is hard to be damaged. Unstable failure easily occurs on the face-sheet between two rows piles, which is the main failure cause of the composite. The fibers play a major role in bearing, and the resin plays a minor role microscopically. The failure mode is the resin fracture, and the interfacial de-bonding between fibers and resin when the composite is loaded with 3 mm displacement compression.

Key words: glass fiber/epoxy resin sandwich composite, numerical simulation, side compressive properties, failure mechanism, failure mode

中图分类号: 

  • TB332

图1

玻璃纤维/环氧树脂基夹芯材料细观结构模型"

表1

玻璃纤维和树脂基体的刚度常数"

组分 E11/
GPa		 E22/
GPa		 E33/
GPa		 G12/
GPa		 G23/
GPa		 G13/
GPa		 ν12 ν23 ν13
S-玻璃纤维 85 40 40 35 23 35 0.3 0.23 0.3
环氧树脂 3.5 3.5 3.5 1.3 1.3 1.3 0.35 0.35 0.35

表2

玻璃纤维和树脂基体的强度常数"

组分 XT YT ZT XC YC ZC S12 S23 S31
S-玻璃纤维 3 530 1 500 1 500 -5 300 -1 000 -1 000 1 000 800 1 000
环氧树脂 70 70 70 -100 -100 -100 30 30 30

图2

划分网格后的细观模型"

图3

玻璃纤维/环氧树脂基夹芯材料的侧压应力与应变云图"

图4

面板的应力放大云图"

图5

压缩破坏后的玻璃纤维/环氧树脂基夹芯材料"

图6

玻璃纤维/环氧树脂基夹芯材料各组分的应力、应变云图"

[1] LI M, WANG S K, ZHANG Z G. Effect of structure on the mechanical behaviors of three-dimensional spacer fabric composites[J]. Applied Composite Materials, 2009,16(1):1-14.
[2] 周光明, 薄晓莉, 匡宁. 整体中空夹层复合材料的弹性性能分析[J]. 复合材料学报, 2010,27(1):185-189.
ZHOU Guangming, BO Xiaoli, KUANG Ning. Analysis of elastic property for hollow integrated sandwich composites[J]. Acta Materiae Compositae Sinica, 2010,27(1):185-189.
[3] SHYR T W, PAN Y H. Low velocity impact responses of hollow core sandwich laminate and interply hybrid laminate[J]. Composite Structures, 2004,64(2):189-198.
[4] 高爱君, 李敏, 王绍凯, 等. 三维间隔连体织物复合材料力学性能[J]. 复合材料学报, 2008,25(2):87-93.
GAO Aijun, LI Min, WANG Shaokai, et al. Experimental study on the mechanical characteristics of 3-D spacer fabric composites[J]. Acta Materiae Compositae Sinica, 2008,25(2):87-93.
[5] 周光明, 钟志珊, 张立泉, 等. 整体中空夹层复合材料力学性能的实验研究[J]. 南京航空航天大学学报, 2007,39(1):11-15.
ZHOU Guangming, ZHONG Zhishan, ZHANG Liquan, et al. Experimental investigation on mechanical properties of hollow integrated sandwich composites[J]. Journal of Nanjing University of Aeronautics & Astronauties, 2007,39(1):11-15.
[6] CAO Haijian, QIAN Kun, WEI Qufu, et al. Low-velocity impact behavior of 3-D fibre hollow integrated core sandwich composites[J]. Polymers & Polymer Composites, 2010,18(4):175-179.
[7] HOSUR M V, ADBULLAH M, JEELANI S. Manufacturing and low-velocity impact characterization of hollow integrated core sandwich composites with hybrid face sheets[J]. Composite Structures, 2004,65:103-115.
[8] 姚秀冬, 周叮, 刘伟庆. 复合材料夹层板芯层内树脂柱对性能的影响[J]. 材料科学与工程学报, 2009,27(6):37-941.
YAO Xiudong, ZHOU Ding, LIU Weiqing. Effects of resinic columns on composited sandwich plates[J]. Journal of Materials Science & Engineering, 2009,27(6):937-941.
[9] 邹建胜, 曾建江, 童明波, 等. 不同夹芯复合材料夹层结构的剪切破坏行为[J]. 机械工程材料, 2012,36(9):38-41.
ZOU Jiansheng, ZENG Jianjiang, TONG Mingbo, et al. Shear damage behavior of composite sandwich plate with different cores[J]. Materials for Mechanical Engineering, 2012,36(9):38-41.
[10] ALBERTO C, EGIDIO R, ENRICO P. Experimental characterization and numerical simulations of a syntactic-foam/glass-fibre composite sandwich[J]. Composites Science and Technology, 2000,60:2169-2180.
[11] VUURE A W, IVENS J A, VERPOEST I. Mechanical properties of composite panels based on woven sandwich-fabric preforms[J]. Composites: Part A, 2000,31:671-680.
[12] WANG M Y, CAO H J, QIAN K. Mechanical properties of three-dimensional fabric sandwich composites[J]. Journal of Engineered Fibers and Fabrics, 2014,9(3):1-7.
[1] 初曦, 邱华. 不同压强条件下环锭旋流喷嘴内部流场模拟[J]. 纺织学报, 2020, 41(09): 33-38.
[2] 丁宁, 林洁. 非稳态自然对流换热系数计算方法及其在防护服隔热预报中的运用 [J]. 纺织学报, 2020, 41(01): 139-144.
[3] 李斯湖, 沈敏, 白聪, 陈亮. 喷气织机辅助喷嘴结构参数对流场特性的影响[J]. 纺织学报, 2019, 40(11): 161-167.
[4] 陈旭, 吴炳洋, 范滢, 杨木生. 蓄热调温织物低温防护过程的数值模拟[J]. 纺织学报, 2019, 40(07): 163-168.
[5] 谷元慧, 张典堂, 贾明皓, 钱坤. 碳纤维增强编织复合材料圆管制备及其压缩性能[J]. 纺织学报, 2019, 40(07): 71-77.
[6] 郑振荣, 智伟, 韩晨晨, 赵晓明, 裴晓园. 碳纤维织物在热流冲击下的热传递数值模拟[J]. 纺织学报, 2019, 40(06): 38-43.
[7] 郭臻, 李新荣, 卜兆宁, 袁龙超. 喷气涡流纺中纤维运动的三维数值模拟[J]. 纺织学报, 2019, 40(05): 131-135.
[8] 广少博, 金玉珍, 祝晓晨. 喷气织机延伸喷嘴内气流场特性分析[J]. 纺织学报, 2019, 40(04): 135-139.
[9] 刘倩楠, 张涵, 刘新金, 苏旭中. 基于ABAQUS的三原组织机织物拉伸力学性能模拟[J]. 纺织学报, 2019, 40(04): 44-50.
[10] 尚珊珊, 郁崇文, 杨建平, 钱希茜. 喷气涡流纺纺纱过程中的气流场数值模拟[J]. 纺织学报, 2019, 40(03): 160-167.
[11] 史倩倩, 高备, 林惠婷, 张玉泽, 汪军. 传统型与双喂给转杯纺纺纱器及其成纱性能对比[J]. 纺织学报, 2019, 40(02): 63-68.
[12] 闫琳琳 邹专勇 卫国 程隆棣. 基于螺旋导引槽空心锭子的喷气涡流纺加捻腔流场模拟[J]. 纺织学报, 2018, 39(09): 139-145.
[13] 胥光申 孔双祥 刘洋 罗时杰. 基于Fluent的喷气织机辅助喷嘴综合性能[J]. 纺织学报, 2018, 39(08): 124-129.
[14] 杨瑞华 刘超 薛元 高卫东. 转杯复合纺成纱器内流场模拟及纱线质量分析[J]. 纺织学报, 2018, 39(03): 26-30.
[15] 林惠婷 汪军. 纤维在输纤通道气流场中运动的模拟[J]. 纺织学报, 2018, 39(02): 55-61.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
京ICP备14006648号　 京公网安备11010502044800号
版权所有 © 2021 《纺织学报》编辑部
地址： 北京市朝阳区延静里中街3号主楼6层《纺织学报》杂志社　邮政编码：100025　
电话：010-65017711,65917740　传真：010-65016539　Email:fangzhixuebao@vip.126.com
本系统由北京玛格泰克科技发展有限公司设计开发